The modern UK standards and regulations for electrical wiring no longer differ substantially from those in other European countries. However, there are a number of noteworthy national peculiarities, habits and traditions associated with domestic electrical wiring in the UK (and Ireland) that differ significantly from other countries. These, along with their historic background, are the focus of this article. They include:

• ring circuits
• fused plugs
• switched sockets
• absence of normal switches and sockets in bathrooms (except for special pull-cord ceiling switches and "razor sockets" with built-in isolation transformer)
• historic wiring colours
• asymmetric supply-voltage tolerances

Legal basis

In England and Wales, the Building Regulations (Approved Document: Part P) require that domestic electrical installations are designed and installed safely according to the "fundamental principles" given in British Standard BS 7671 Chapter 13. These are very similar to the fundamental principles defined in international standard IEC 60364-1 and equivalent national standards in other countries. Accepted ways for fulfilling this legal requirement include The UK building regulations are statutory instruments that seek to ensure that the policies set out in the Building Act 1984 are carried out in the construction of buildings. ... British Standards is the new name of the British Standards Institute and is part of BSI Group which also includes a testing organisation. ... Standards are produced by many organizations, some for internal usage only, others for use by a groups of people, groups of companies, or a subsection of an industry. ... IEC 60364 is the International Electrotechnical Commissions international standard on electrical installations of buildings. ...

• the rules of the IEE wiring regulations (BS 7671), colloquially referred to as "the regs";
• the rules of an equivalent standard approved by a member of the EEA (e.g., DIN/VDE 0100);
• guidance given in installation manuals that are consistent with BS 7671, such as the IEE On-Site Guide and IEE Guidance Notes Nos 1 to 7.
• BS 7671's 16th Edition to become 17th Edition from June 2008.

Installations in commercial premises must satisfy various safety legislation, such as the Electricity at Work Regulations 1989. Not to be confused with the Institute of Electrical and Electronics Engineers (IEEE, I-triple-E). ... BS 7671 is a publication from the IET (Formerly known as The IEE) in agreement with the BSI British Standards Institute (UK). ...  EFTA countries (except Switzerland)  EU countries Together these form the EEA. The European Economic Area (EEA) came into being on January 1, 1994 following an agreement between the European Free Trade Association (EFTA) and the European Union (EU). ... Look up din in Wiktionary, the free dictionary. ... The VDE is the German Association for Electrical, Electronic and Information Technologies, a professional body based in Frankfurt am Main. ...

Wiring colours

The standard wiring colours in the UK are (as of 2006) the same as elsewhere in Europe and Australia and follow international standard IEC 60446. This colour scheme had already been introduced for appliance flexes in the UK in the early 1970s, however the IEE recommended a different scheme for fixed wiring until 2006. As a result, the international standard blue/brown scheme is as of 2006 found in all but the oldest appliance flexes. In fixed wiring, the blue/brown scheme is only found in very new (post-2004) installations, and electricians are likely to encounter the old IEE black/red scheme in existing installations for many more decades. International standard IEC 60446 defines basic safety principles for identifying electrical conductors by colours or numerals, for example in electricity distribution wiring. ...

The standard colours in fixed wiring were harmonized in 2004 with the regulations in other European countries and the international IEC 60446 standard. For a transitional period (April 2004 – March 2006) either set of colours were allowed (but not both), provided that any changes in the colour scheme are clearly labelled. From April 2006, only the new colours should be used for any new wiring. Ground or earth in a mains (AC power) electrical wiring system is a conductor that exists primarily to provide a low impedance path to the earth to prevent the buildup of voltages, static or transient (lightning), that may result in undue hazards to connected equipment or persons, and which in... Year 2004 (MMIV) was a leap year starting on Thursday of the Gregorian calendar. ... International standard IEC 60446 defines basic safety principles for identifying electrical conductors by colours or numerals, for example in electricity distribution wiring. ...

The colour change has been controversial and was delayed for three decades, because the colour blue which was previously used as a phase colour is now the colour for neutral, and the colour black which was previously used for neutral now indicates a phase. While confusion in identification of these conductors could be dangerous, the combinations of colours used usually resolves ambiguities. The installation of cables with the 'new' colours in an installation where the 'old' colours exist, could leave the way open for confusion; it is important in such situations that consideration is given to correct identification of the cables – with the use of marker tags if necessary. It has also been suggested that the new phase colours are difficult to distinguish in low-light conditions, but the same can be claimed for most colour combinations, including the old British phase colours. A mnemonic advantage of the new colours is that the first two letters of "BLue" and "BRown" match the corresponding positions on the BS 1363 socket face: "bottom left" (neutral) and "bottom right" (live). BS1363 type electrical socket. ...

Ring circuits

UK electrical power circuits are normally described as either radial or ring.

A radial circuit is one where power is transmitted from point to point by a single length of cable linking each point to the next. It starts at the main switch or fuse and simply terminates at the last connected device. It may branch at a connection point. Lighting circuits are normally wired in this way, but it may also be used for low power socket circuits.

A British peculiarity unknown in many other national wiring codes is the ring circuit. A cable starts at the supply point and goes to each device in the same way as with a radial. The last device is connected back to the supply so that the whole circuit forms a continuous ring. The primary advantage is to allow more power to be supplied than could otherwise be carried with a given size of cable. A ring circuit (more formally a ring final circuit; informally a ring main or just a ring) is an electrical wiring technique that provides two paths for the live, neutral and earth lines by wiring a ring of cable, or sometimes three separate cores in conduit. ...

Cables are most commonly a single outer sheath containing separately insulated live and neutral wires, and a non-insulated protective earth to which sleeving is added when exposed. Standard sizes have a conductor cross sectional area of 1, 1.5, 2.5, 4, 6 and 10 square millimetres. Sizes 1 or 1.5 are typically used for 6 or 10 ampere lighting circuits and 2.5 for socket circuits. The protective earth conductor is normally one standard size smaller than the main conductors.

Regulations

All electrical work within a domestic setting must comply with British Standard 7671. Although this standard is older, the legal enforceability is a requirement of "Part P" of the building regulations in England and Wales introduced on 1st January 2005.

Some of the restrictions introduced with Part P were controversial, especially the rules surrounding work carried out by non-professional (or, more accurately, unregistered) people such as DIYers. Under the new regulations, commencement of any work other than simple changes becomes notifiable to the local building control authority; "other than simple" in this context means any work in a kitchen or bathroom other than like-for-like replacement, work in other areas more than just adding extra lights or sockets to an existing circuit or meeting certain other criteria, such as outdoor wiring.

To coincide with the new regulations, the Government approved several professional bodies to award "competent persons" status to individuals and this allows them to "self-certify" work they carry out. The building control authority must be informed of any notifiable work carried out by someone not qualified under this scheme before it is started (unless it is an emergency) and must subsequently be approved by them. Originally, it was widely understood that inspection by a qualified person (leading to authority approval) must be organised and paid for by the home-owner or person responsible for the site and this caused some considerable criticism.

One of the quirks of Part P is that in some cases the installation of 12V downlighters is notifiable where as the installation of 240V mains downlighters isn't. This appears strange but it's because 12V downlighters draw high currents and that combined with the wrong choice of wire could lead to a fire.

On 6th April 2006, Part P was amended to clarify the actual requirements around certification of DIY work (or work completed by someone otherwise unable to self-certify) and to "make enforcement more proportionate to the risk"^[1].

The 2006 amendment makes it clear that it is the responsibility of the building control authority to issue the necessary certificate (a Building Regulations Completion Certificate) once work has been completed. Any inspection required to safely issue that certificate must be determined by, and paid for by, the building control authority. This can be done "in house" or they may contract the work out to specialist body. Note that although any inpsections are at the expense of the building authority, notification of building work is a formal process and a building control fee is payable.

Installation accessories

Many accessories for electrical installations (e.g., wall sockets, switches) sold in the UK are designed to fit into the mounting boxes defined in BS 4662, with a 86 mm × 86 mm square face plate that is fixed to the rest of the enclosure by two M3.5 screws (typ. 25 or 40 mm long) located on a horizontal center line, 60.3 mm apart. Double face plates for BS 4662 boxes measure 143 mm × 86 mm and have the two screws 120.6 mm apart. Image File history File linksMetadata Download high-resolution version (903x600, 456 KB)[edit] Summary This image is a digital photograph taken by myself on 17/06/06. ... British Standards is the new name of the British Standards Institute and is part of BSI Group which also includes a testing organisation. ... The metric ISO screw threads are the world-wide most commonly used type of general-purpose screw thread. ...

Where less common accessories (e.g., home-automation control elements from non-UK manufacturers) are installed that are not available in BS 4662 format, other standard mounting boxes may occasionally have to be used, such as those defined in DIN 49073-1 (60 mm diameter, 45 mm deep, fixing screws 60 mm apart) or – less commonly in the UK – ANSI/NEMA OS-1. Look up din in Wiktionary, the free dictionary. ... The National Electrical Manufacturers Association or NEMA is a U.S.-based association, which was created on September 1, 1926, when the Associated Manufacturers of Electrical Supplies and the Electric Power Club merged. ...

The commonly used domestic wall-mount socket used in the UK for currents up to 13 A is defined in BS 1363-2 and normally includes a switch. For higher currents or three-phase supplies, IEC 309 sockets are used instead. BS1363 type electrical socket. ... IEC 309 (now IEC 60309, 1999) is an international standard from the International Electrotechnical Commission for plugs, socket-outlets and couplers for industrial purposes. It specifies a range of mains power connectors with circular housings, and different numbers and arrangements of pins for different applications. ...

Plug and accessory fuses

Some accessories require protection at a lower current than that provided by the ring main protection device. The protection device used in such accesories is a 25 mm ceramic cartridge fuse, rated at 3 A, 5 A, or 13 A.

In the case of permanently connected equipment the fuse is contained in a holder mounted in an accessory known as a fused spur box, which usually includes an isolator switch and often a neon bulb to indicate if the equipment is powered. In this case the fuse protects the spur (equipment supply) cable and any switch contacts.

In the case of non-permanently connected domestic equipment, a socket rated at 13 A is attached to the ring main, into which a fused plug may be inserted. The fuse protects the contacts (including any switch contacts) and the equipment flex. There are two benefits to this arrangement. Firstly with low power equipment a flex with a low current rating (and therefore minimal diameter) can be used. Secondly, if the equipment is moved to a different socket, it will remain protected by the same (hopefully correct) fuse. The disadvantage is that despite warnings to the contrary people often use a fuse rated at too high a current, or even wrap a blown fuse in aluminium foil, meaning that under fault conditions the contacts and flex will be subjected to anything up to the maximum ring main current. This is likely to cause a fire.

Note that the equipment itself should have its own protection measures, such as another fuse, unless the plug or accessory fuse affords all required protection (as is the case with most table lamps, for example). It is also important to be aware that when a double socket is rated at 13A this applies to the total rating of the two sockets together. Therefore the use of a double socket for powering more than one highly rated appliance, such as a washing machine and clothes dryer, is unsafe. Front-loading washing machine. ... An electric clothes dryer A clothes dryer or tumble dryer is a household appliance that is used to remove the residual moisture from a load of clothing and other textiles, generally shortly after they are cleaned in a washing machine. ...

Consumer unit

A domestic supply typically consists of a large cable entering the house which is connected to a sealed box containing the main supply fuse. This will typically have a value from 60–100 A. Separate live and neutral cables go from here to a meter, and from there proceed to one or more consumer units. This contains a main switch and individual fuses or Miniature Circuit Breakers (MCBs) for each circuit. 200 A Industrial fuse. ... A 2 pole miniature circuit breaker A circuit breaker is an automatically-operated electrical switch designed to protect an electrical circuit from damage caused by overload or short circuit. ... A 2 pole miniature circuit breaker A circuit breaker is an automatically-operated electrical switch designed to protect an electrical circuit from damage caused by overload or short circuit. ...

Special locations

Bathrooms

The installation of electrical devices in bathrooms and shower rooms is regulated in Section 601 of BS 7671, and Part B of the Building Regulations. For such rooms, four special zones are defined [1], in which additional protection is required for electrical facilities:

• Zone 0 is the smallest rectangular volume that contains the bathtub, shower basin, etc.
• Zone 1 is the area above Zone 0, up to a height of 2.25 m above the floor.
• Zone 2 is the area above Zone 1 up to a height of 3 m, as well as the area that is horizontally within 0.6 m from Zone 1.
• Zone 3 is the area above Zone 2 up to a height of 3 m, as well as the area that is horizontally within 2.4 m from Zone 2.

Within Zone 0, only Separated Extra Low Voltage devices are permitted. Any AC transformer supplying such a device must be located outside Zones 0–2. The minimum required [[IP Code|ingress protection rating in Zone 0 is IPX7 and IPX4 in Zone 1 and 2. If water jets are likely to occur, at least IPX5 is required in Zone 1–3. Otherwise, in Zone 3 and beyond, an ingress protection rating of IP20 is the minimum required. Equipment in Zone 1–3 must be protected by a 30 mA residual-current circuit breaker (except for shower pumps and shower heaters, where the use of an RCD is so far only recommended). A bathtub A bathtub (AmE) or bath (BrE) is a plumbing fixture used for bathing. ... It has been suggested that Steam shower be merged into this article or section. ... The use of extra low voltage (ELV) in an electrical circuit is one of several means to provide protection against electrical shock. ... The IP code or IP rating defined in international standard IEC 60529 classifies the level of protection that electrical appliances provide against the intrusion of solid objects or dust, accidental contact, and water. ... The IP Code defined in international standard IEC 60529 classifies the level of protection that electrical appliances provide against the intrusion of solid objects or dust, accidental contact, and water. ... In electrical engineering, residual current circuit breakers (RCCB) or residual current devices (RCD) are circuit breakers that operate to disconnect their circuit whenever they detect that current leaking out of the circuit (such as current leaking to earth through a ground fault) exceeds safety limits. ...

Shaving sockets (with isolating transformer) are permitted in Zone 2 if direct spray from a shower is unlikely, even if they are only IP20. In a bathroom or shower room, such shaving sockets are the only sockets permitted in the entire room. In any other room with a bathtub or shower, normal sockets are permitted as long as they are outside Zone 3.

(Earlier British wiring rules in bathrooms used to be far more restrictive, leading to British peculiarities in bathrooms such as the use of cord switches. The 2001 edition of the Wiring Regulations is more flexible now, placing restrictions on bathroom installations that are now more similar to those in other European countries. The forthcoming 17th Edition of the Regulations is likely to allow 13A sockets in bathrooms, subject to zoning and protection by a 30mA Residual Current Device.)

Swimming pools

For swimming pools, Section 603 of BS 7671 defines similar zones. In some of these zones, only industrial sockets according to IEC 60309 are permitted, in order to discourage the use of portable domestic appliances with inappropriate ingress protection rating. IEC 309 (now IEC 60309, 1999) is an international standard from the International Electrotechnical Commission for plugs, socket_outlets and couplers for industrial purposes. It specifies a range of mains power connectors with circular housings, and different numbers and arrangements of pins for different applications. ... The IP Code defined in international standard IEC 60529 classifies the level of protection that electrical appliances provide against the intrusion of solid objects or dust, accidental contact, and water. ...

Portable outdoor equipment

For use outdoors or in other wet locations (but not bathrooms) special sockets are made. These can be divided into three main groups, industrial sockets which are totally different from the standard sockets, sockets with the same pinout as normal sockets but that will only seal properly when the correct plug and socket are used together (e.g. the 5 A 13 A and 15 A variants of Lewden sockets) and sockets that completely enclose a normal plug with a seal around the flex (e.g. MK masterseal). Industrial power plug is used here to refer to those power connectors that, unlike ordinary mains power plugs, are not used for the average domestic appliance but rather for more heavy-duty applications such as arc welders, cranes, cinemas, large cooking ranges, etc. ... MK electric is a company that makes electrical accessories (plugs sockets switches conduit trunking etc). ...

Sockets that are outside or can "feasibly supply equipment outside the equipotential zone" (a wording that is fairly ambiguous and the exact interpretation of which is subject to some controversy) should be protected by a 30 mA or lower RCD to provide additional safety. A residual current device (RCD) A residual current device (RCD), or residual current circuit breaker (RCCB), is an electrical wiring device that disconnects a circuit whenever it detects that the flow of current is not balanced between the phase (hot) conductor and the neutral conductor. ...

Supply voltage

Since 1960, the supply voltage in Great Britain in domestic premises has been 240 V AC (rms) at 50 Hz while in Northern Ireland it was 220 V. In 1988, a Europe-wide agreement was reached to change the various national voltages, which ranged at the time from 220 V to 240 V, to a common European standard of 230 V (CENELEC Harmonization Document HD 472 S1:1988). City lights viewed in a motion blurred exposure. ... In mathematics, the root mean square or rms is a statistical measure of the magnitude of a varying quantity. ... This article is about the SI unit of frequency. ...

As a result, the standard nominal supply voltage in domestic single-phase 50 Hz installations in the UK has been 230 V AC (rms) since 1 January 1995 (Electricity Supply Regulations, SI 1994, No. 3021). However, as an interim measure, electricity suppliers can work with an asymmetric voltage tolerance of 230 V +10%/−6% (216.2 V to 253 V). This was supposed to be widened to 230 V ±10% (207 V to 253 V), but the time of this change has been put back repeatedly and currently sits in 2008 (BS 7697). The old standard was 240 V ±6% (225.6 V to 254.4 V), which is mostly contained within the new range, and so in practice suppliers have had no reason to actually change voltages. International safety symbol Caution, risk of electric shock (ISO 3864), colloquially known as high voltage symbol. ... In electrical engineering, single-phase electric power refers to the distribution of electric power using a system in which all the voltages of the supply vary in unison. ... This article is about the SI unit of frequency. ... City lights viewed in a motion blurred exposure. ... In mathematics, the root mean square or rms is a statistical measure of the magnitude of a varying quantity. ... Year 1995 (MCMXCV) was a common year starting on Sunday (link will display full 1995 Gregorian calendar). ... 2008 (MMVIII) will be a leap year starting on Tuesday of the Gregorian calendar. ...

The continued deviation in the UK from the harmonised European voltage has been criticised in particular by light bulb manufacturers, who require tighter voltage tolerances to optimise the operating temperature and lifetime of their products, and who currently have to continue producing separate 230 V and 240 V versions. The light bulb is one of the most significant inventions in the history of the human race, illuminating the darkness of the evening and bringing light indoors at all times in order focus on the task at hand. ...

See also

• Electric power
• Technical standards in colonial Hong Kong

For delivered electrical power, see Electrical power industry. ... This article gives readers an insight on how the British colonial rule affected the technical standards in Hong Kong. ...

References

• Part P of Approved Documents, The Building Regulations 2000: Electrical safety.
• The Electricity at Work Regulations 1989
• BS 4662: Specification for boxes for the enclosure of electrical accessories. British Standards Institute, 1970.

Year 2007 (MMVII) is the current year, a common year starting on Monday of the Gregorian calendar and the AD/CE era in the 21st century. ... is the 301st day of the year (302nd in leap years) in the Gregorian calendar. ... The UK building regulations are statutory instruments that seek to ensure that the policies set out in the Building Act 1984 are carried out in the construction of buildings. ... British Standards is the new name of the British Standards Institute and is part of BSI Group which also includes a testing organisation. ...

External links

• IEE Wiring Regulations
• The Electrician's Guide to the 16th Edition IEE Regulations
• Electrical Safety at Work, Health & Safety Executive
• Electrical standards and approved codes of practice, Health & Safety Executive
• The Electrical Equipment (Safety) Regulations 1994
• The Plugs and Sockets etc. (Safety) Regulations 1994
• The Electricity Safety, Quality and Continuity Regulations 2002
• General Cable - Imperial / Metric Conductor Size Comparison Chart
• Meeting the requirements of EaWR 1989
• Wiring a standard UK plug