NationMaster - Encyclopedia: Gas metal arc welding

Gas metal arc welding (GMAW), sometimes referred to by its subtypes metal inert gas (MIG) welding or metal active gas (MAG) welding, is a semi-automatic or automatic arc welding process in which a continuous and consumable wire electrode and a shielding gas are fed through a welding gun. A constant voltage, direct current power source is most commonly used with GMAW, but constant current systems, as well as alternating current, can be used. There are four primary methods of metal transfer in GMAW, called globular, short-circuiting, spray, and pulsed-spray, each of which has distinct properties and corresponding advantages and limitations. Image File history File linksMetadata Download high resolution version (1960x2213, 3402 KB) A man gas metal arc welding. ... Image File history File linksMetadata Download high resolution version (1960x2213, 3402 KB) A man gas metal arc welding. ... Welding is a fabrication process that joins materials, usually metals or thermoplastics, by causing coalescence. ... A wire is a single, usually cylindrical, elongated strand of drawn metal. ... For other uses, see Electrode (disambiguation). ... Shielding gases are inert or semi-inert gases that are commonly used in several welding processes, most notably gas metal arc welding and gas tungsten arc welding. ... Josephson junction array chip developed by NIST as a standard volt. ... Direct current (DC or continuous current) is the continuous flow of electricity through a conductor such as a wire from high to low potential. ... In electricity, current refers to electric current, which is the flow of electric charge. ... City lights viewed in a motion blurred exposure. ...

Originally developed for welding aluminum and other non-ferrous materials in the 1940s, GMAW was soon applied to steels because it allowed for lower welding time compared to other welding processes. The cost of inert gas limited its use in steels until several years later, when the use of semi-inert gases such as carbon dioxide became common. Further developments during the 1950s and 1960s gave the process more versatility and as a result, it became a highly used industrial process. Today, GMAW is the most common industrial welding process, preferred for its versatility, speed and the relative ease of adapting the process to robotic automation. The automobile industry in particular uses GMAW welding almost exclusively. Unlike welding processes that do not employ a shielding gas, such as shielded metal arc welding, it is rarely used outdoors or in other areas of air volatility. A related process, flux cored arc welding, often does not utilize a shielding gas, instead employing a hollow electrode wire that is filled with flux on the inside. Aluminum redirects here. ... For other uses, see Steel (disambiguation). ... Carbon dioxide is a chemical compound composed of two oxygen atoms covalently bonded to a single carbon atom. ... â€œCarâ€ and â€œCarsâ€ redirect here. ... Shielded metal arc welding Shielded metal arc welding (SMAW), also known as manual metal arc (MMA) welding or informally as stick welding, is a manual arc welding process that uses a consumable electrode coated in flux to lay the weld. ... A wire feeder configured for . ... In metallurgy, flux is a substance which removes passivating oxides from the surface of a metal or alloy. ...

Development

The principles of gas metal arc welding began to be developed around the turn of the 19th century, with Humphry Davy's discovery of the electric arc in 1800. At first, carbon electrodes were used, but by the late 1800s, metal electrodes had been invented by N.G. Slavianoff and C. L. Coffin. In 1920, an early predecessor of GMAW was invented by P. O. Nobel of General Electric. It used a bare electrode wire and direct current, and used arc voltage to regulate the feed rate. It did not use a shielding gas to protect the weld, as developments in welding atmospheres did not take place until later that decade. In 1926 another forerunner of GMAW was released, but it was not suitable for practical use.^[1] Sir Humphry Davy, 1st Baronet, FRS (17 December 1778 â€“ 29 May 1829) was a British chemist and physicist. ... A 3000 volt electricity arc between two nails Electricity arcs between the power rail and electrical pickup shoe on a London Underground train An electric arc can melt calcium oxide An electric arc is an electrical breakdown of a gas which produces an ongoing plasma discharge, resulting from a current... C.L. Coffin of Detroit was awarded a U.S. patent for an arc welding process using a metal electrode. ... â€œGEâ€ redirects here. ...

It was not until 1948 that GMAW was finally developed by the Battelle Memorial Institute. It used a smaller diameter electrode and a constant voltage power source, which had been developed by H. E. Kennedy. It offered a high deposition rate but the high cost of inert gases limited its use to non-ferrous materials and cost savings were not obtained. In 1953, the use of carbon dioxide as a welding atmosphere was developed, and it quickly gained popularity in GMAW, since it made welding steel more economical. In 1958 and 1959, the short-arc variation of GMAW was released, which increased welding versatility and made the welding of thin materials possible while relying on smaller electrode wires and more advanced power supplies. It quickly became the most popular GMAW variation. The spray-arc transfer variation was developed in the early 1960s, when experimenters added small amounts of oxygen to inert gases. More recently, pulsed current has been applied, giving rise to a new method called the pulsed spray-arc variation.^[2]

As noted, GMAW is currently one of the most popular welding methods, especially in industrial environments. It is used extensively by the sheet metal industry and, by extension, the automobile industry. There, the method is often used to do arc spot welding, thereby replacing riveting or resistance spot welding. It is also popular in robot welding, in which robots handle the workpieces and the welding gun to quicken the manufacturing process.^[3] Generally, it is unsuitable for welding outdoors, because the movement of the surrounding atmosphere can dissipate the shielding gas and thus make welding more difficult, while also decreasing the quality of the weld. The problem can be alleviated to some extent by increasing the shielding gas output, but this can be expensive and may also affect the quality of the weld. In general, processes such as shielded metal arc welding and flux cored arc welding are preferred for welding outdoors, making the use of GMAW in the construction industry rather limited. Furthermore, the use of a shielding gas makes GMAW an unpopular underwater welding process, and for the same reason it is rarely used in space applications. A miller spot welder Spot welding is a type of resistance welding used to weld various sheet metals. ... Solid rivets Metal wheel with riveted spokes and tyre. ... Resistance welding refers to a group of welding processes that produce coalescence of the faying surfaces with the heat obtained from resistance of the workpieces to the flow of the welding current in a circuit of which the workpieces are part, and by the application of pressure. ... Spot welding: KUKA industrial robots welding a car body in the white section of a production line. ... Shielded metal arc welding Shielded metal arc welding (SMAW), also known as manual metal arc (MMA) welding or informally as stick welding, is a manual arc welding process that uses a consumable electrode coated in flux to lay the weld. ... A wire feeder configured for . ... Underwater welding Underwater welding refers to a number of distinct welding processes that are performed underwater. ... This article is about the idea of space. ...

Equipment

To perform gas metal arc welding, the basic necessary equipment is a welding gun, a wire feed unit, a welding power supply, an electrode wire, and a shielding gas supply. A high output constant current welding power supply for use with GTAW and SMAW A welding power supply is an electrical device that provides an electrical current to perform welding procedures which require electricity. ... Shielding gases are inert or semi-inert gases that are commonly used in several welding processes, most notably gas metal arc welding and gas tungsten arc welding. ...

Welding gun and wire feed unit

The typical GMAW welding gun has a number of key parts—a control switch, a contact tip, a power cable, a gas nozzle, an electrode conduit and liner, and a gas hose. The control switch, or trigger, when pressed by the operator, initiates the wire feed, electric power, and the shielding gas flow, causing an electric arc to be struck. The contact tip, normally made of copper and sometimes chemically treated to reduce spatter, is connected to the welding power source through the power cable and transmits the electrical energy to the electrode while directing it to the weld area. It must be firmly secured and properly sized, since it must allow the passage of the electrode while maintaining an electrical contact. Before arriving at the contact tip, the wire is protected and guided by the electrode conduit and liner, which help prevent buckling and maintain an uninterrupted wire feed. The gas nozzle is used to evenly direct the shielding gas into the welding zone—if the flow is inconsistent, it may not provide adequate protection of the weld area. Larger nozzles provide greater shielding gas flow, which is useful for high current welding operations, in which the size of the molten weld pool is increased. The gas is supplied to the nozzle through a gas hose, which is connected to the tanks of shielding gas. Sometimes, a water hose is also built into the welding gun, cooling the gun in high heat operations.^[4] Download high resolution version (796x723, 284 KB)1) from MIG torch handle with finger trigger. ... Download high resolution version (796x723, 284 KB)1) from MIG torch handle with finger trigger. ... Image File history File links Download high resolution version (1712x1341, 860 KB) Overview This is a picture of the side of a Miller D60 welding wire feeder. ... Image File history File links Download high resolution version (1712x1341, 860 KB) Overview This is a picture of the side of a Miller D60 welding wire feeder. ... For other uses, see Copper (disambiguation). ...

The wire feed unit supplies the electrode to the work, driving it through the conduit and on to the contact tip. Most models provide the wire at a constant feed rate, but more advanced machines can vary the feed rate in response to the arc length and voltage. Some wire feeders can reach feed rates as high as 30.5 m/min (1200 in/min),^[5] but feed rates for semiautomatic GMAW typically range from 2 to 10 m/min (75–400 in/min).^[6]

Power supply

Most applications of gas metal arc welding use a constant voltage power supply. As a result, any change in arc length (which is directly related to voltage) results in a large change in heat input and current. A shorter arc length will cause a much greater heat input, which will make the wire electrode melt more quickly and thereby restore the original arc length. This helps operators keep the arc length consistent even when manually welding with hand-held welding guns. To achieve a similar effect, sometimes a constant current power source is used in combination with an arc voltage-controlled wire feed unit. In this case, a change in arc length makes the wire feed rate adjust in order to maintain a relatively constant arc length. In rare circumstances, a constant current power source and a constant wire feed rate unit might be coupled, especially for the welding of metals with high thermal conductivities, such as aluminum. This grants the operator additional control over the heat input into the weld, but requires significant skill to perform successfully.^[7]

Alternating current is rarely used with GMAW; instead, direct current is employed and the electrode is generally positively charged. Since the anode tends to have a greater heat concentration, this results in faster melting of the feed wire, which increases weld penetration and welding speed. The polarity can be reversed only when special emissive-coated electrode wires are used, but since these are not popular, a negatively charged electrode is rarely employed.^[8] Diagram of a zinc anode in a galvanic cell. ...

Electrode

Electrode selection is based primarily on the composition of the metal being welded, but also on the process variation being used, the joint design, and the material surface conditions. The choice of an electrode strongly influences the mechanical properties of the weld area, and is a key factor in weld quality. In general, the finished weld metal should have mechanical properties similar to those of the base material, with no defects such as discontinuities, entrained contaminants, or porosity, within the weld. To achieve these goals a wide variety of electrodes exist. All commercially available electrodes contain deoxidizing metals such as silicon, manganese, titanium, and aluminum in small percentages to help prevent oxygen porosity, and some contain denitriding metals such as titanium and zirconium to avoid nitrogen porosity.^[9] Depending on the process variation and base material being used, the diameters of the electrodes used in GMAW typically range from 0.7 to 2.4 mm (0.028–0.095 in), but can be as large as 4 mm (0.16 in). The smallest electrodes, generally up to 1.14 mm (0.045 in)^[10] are associated with the short-circuiting metal transfer process, while the most common spray-transfer process mode electrodes are usually at least 0.9 mm (0.035 in).^[11]^[12] Not to be confused with Silicone. ... General Name, symbol, number manganese, Mn, 25 Chemical series transition metals Group, period, block 7, 4, d Appearance silvery metallic Standard atomic weight 54. ... General Name, symbol, number titanium, Ti, 22 Chemical series transition metals Group, period, block 4, 4, d Appearance silvery metallic Standard atomic weight 47. ... Aluminum redirects here. ... General Name, Symbol, Number zirconium, Zr, 40 Chemical series transition metals Group, Period, Block 4, 5, d Appearance silvery white Standard atomic weight 91. ... A millimetre (American spelling: millimeter), symbol mm is an SI unit of length that is equal to one thousandth of a metre. ...

Image File history File links Download high resolution version (1016x620, 14 KB) Created by Nathaniel Sheetz, user Spangineer on July 16, 2005. ... Image File history File links Download high resolution version (1016x620, 14 KB) Created by Nathaniel Sheetz, user Spangineer on July 16, 2005. ...

Shielding gas

Shielding gases are necessary for gas metal arc welding to protect the welding area from atmospheric gases such as nitrogen and oxygen, which can cause fusion defects, do not provide adequate weld penetration (argon) or cause an erratic arc and encourage spatter (with helium). Pure carbon dioxide, on the other hand, allows for deep penetration welds but encourages oxide fortransfer GMAW becomes increasingly problematic with thinner electrodes. .^[13] General Name, symbol, number nitrogen, N, 7 Chemical series nonmetals Group, period, block 15, 2, p Appearance colorless gas Standard atomic weight 14. ... General Name, symbol, number oxygen, O, 8 Chemical series nonmetals, chalcogens Group, period, block 16, 2, p Appearance colorless (gas) pale blue (liquid) Standard atomic weight 15. ... Carbon dioxide is a chemical compound composed of two oxygen atoms covalently bonded to a single carbon atom. ...

Argon is also commonly mixed with other gases, such as oxygen, helium, hydrogen, and nitrogen. The addition of up to 5% oxygen (like the higher concentrations of carbon dioxide mentioned above) can be helpful in welding stainless steel or in very thin gauge materials, however, in most applications carbon dioxide is preferred.^[14] Increased oxygen makes the shielding gas oxidize the electrode, which can lead to porosity in the deposit if the electrode does not contain sufficient deoxidizers. Argon-helium mixtures are completely inert, and can be used on nonferrous materials. A helium concentration of 50%–75% raises the voltage and increases the heat in the arc. Higher percentages of helium also improve the weld quality and speed of using alternating current for the welding of aluminum. Hydrogen is sometimes added to argon in small concentrations (up to about 5%) for welding nickel and thick stainless steel workpieces. In higher concentrations (up to 25% hydrogen), it is useful for welding conductive materials such as copper. However, it should not be used on steel, aluminum or magnesium because of the risk of hydrogen porosity. Additionally, nitrogen is sometimes added to argon to a concentration of 25%–50% for welding copper, but the use of nitrogen, especially in North America, is limited. Mixtures of carbon dioxide and oxygen are similarly rarely used in North America, but are more common in Europe and Japan. This article is about the chemistry of hydrogen. ... North America North America is a continent[1] in the Earths northern hemisphere and (chiefly) western hemisphere. ... For other uses, see Europe (disambiguation). ...

Shielding gas mixtures of three or more gases are also available. claiming to improve weld quality. Mixtures of argon, carbon dioxide and oxygen are marketed for welding steels. Other mixtures add a small amount of helium to argon-oxygen combinations, these mixtures reportedly allow higher arc voltages and welding speed. Helium is also sometimes used as the base gas, with small amounts of argon and carbon dioxide added. Additionally, other specialized and often proprietary gas mixtures purport even greater benefits for specific applications.^[15]

The desirable rate of gas flow depends primarily on weld geometry, speed, current, the type of gas, and the metal transfer mode being utilized. Welding flat surfaces requires higher flow than welding grooved materials, since the gas is dispersed more quickly. Faster welding speeds mean that more gas must be supplied to provide adequate coverage. Additionally, higher current requires greater flow, and generally, more helium is required to provide adequate coverage than argon. Perhaps most importantly, the four primary variations of GMAW have differing shielding gas flow requirements—for the small weld pools of the short circuiting and pulsed spray modes, about 10 L/min (20 ft³/h) is generally suitable, while for globular transfer, around 15 L/min (30 ft³/h) is preferred. The spray transfer variation normally requires more because of its higher heat input and thus larger weld pool; along the lines of 20–25 L/min (40–50 ft³/h).^[16] The litre or liter (see spelling differences) is a unit of volume. ... A foot (plural: feet or foot;[1] symbol or abbreviation: ft or, sometimes, â€² â€“ a prime) is a unit of length, in a number of different systems, including English units, Imperial units, and United States customary units. ... The hour (symbol: h) is a unit of time. ...

Operation

In most of its applications, gas metal arc welding is a fairly simple welding process to learn, requiring no more than several days to master basic welding technique. Even when welding is performed by well-trained operators, however, weld quality can fluctuate, since it depends on a number of external factors. And all GMAW is dangerous, though perhaps less so than some other welding methods, such as shielded metal arc welding.^[17] Image File history File links Download high resolution version (1188x1024, 523 KB) Diagram created by Nathaniel Sheetz on June 6, 2005. ... Image File history File links Download high resolution version (1188x1024, 523 KB) Diagram created by Nathaniel Sheetz on June 6, 2005. ... Shielded metal arc welding Shielded metal arc welding (SMAW), also known as manual metal arc (MMA) welding or informally as stick welding, is a manual arc welding process that uses a consumable electrode coated in flux to lay the weld. ...

Technique

The basic technique for GMAW is quite simple, since the electrode is fed automatically through the torch. By contrast, in gas tungsten arc welding, the welder must handle a welding torch in one hand and a separate filler wire in the other, and in shielded metal arc welding, the operator must frequently chip off slag and change welding electrodes. GMAW requires only that the operator guide the welding gun with proper position and orientation along the area being welded. Keeping a consistent contact tip-to-work distance (the stickout distance) is important, because a long stickout distance can cause the electrode to overheat and will also waste shielding gas. Stickout distance varies for different GMAW weld processes and applications.^[18] For short-circuit transfer, the stickout is generally 1/4 inch to 1/2 inch, for spray transfer the stickout is generally 1/2 inch. The position of the end of the contact tip to the gas nozzle are related to the stickout distance and also varies with transfer type and application. The orientation of the gun is also important—it should be held so as to bisect the angle between the workpieces; that is, at 45 degrees for a fillet weld and 90 degrees for welding a flat surface. The travel angle or lead angle is the angle of the torch with respect to the direction of travel, and it should generally remain approximately vertical. However, the desirable angle changes somewhat depending on the type of shielding gas used—with pure inert gases, the bottom of the torch is out often slightly in front of the upper section, while the opposite is true when the welding atmosphere is carbon dioxide.^[19] Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding process that uses a nonconsumable tungsten electrode to produce the weld. ...

Quality

Two of the most prevalent quality problems in GMAW are dross and porosity. If not controlled, they can lead to weaker, less ductile welds. Dross is an especially common problem in aluminum GMAW welds, normally coming from particles of aluminum oxide or aluminum nitride present in the electrode or base materials. Electrodes and workpieces must be brushed with a wire brush or chemically treated to remove oxides on the surface. Any oxygen in contact with the weld pool, whether from the atmosphere or the shielding gas, causes dross as well. As a result, sufficient flow of inert shielding gases is necessary, and welding in volatile air should be avoided.^[20] Dross is a mass of solid impurities floating on a molten metal bath. ... Porosity is a measure of the void spaces in a material, and is measured as a fraction, between 0â€“1, or as a percentage between 0â€“100%. The term porosity is used in multiple fields including manufacturing, earth sciences and construction. ... Ductility is the physical property of being capable of sustaining large plastic deformations without fracture (in metals, such as being drawn into a wire). ...

In GMAW the primary cause of porosity is gas entrapment in the weld pool, which occurs when the metal solidifies before the gas escapes. The gas can come from impurities in the shielding gas or on the workpiece, as well as from an excessively long or violent arc. Generally, the amount of gas entrapped is directly related to the cooling rate of the weld pool. Because of its higher thermal conductivity, aluminum welds are especially susceptible to greater cooling rates and thus additional porosity. To reduce it, the workpiece and electrode should be clean, the welding speed diminished and the current set high enough to provide sufficient heat input and stable metal transfer but low enough that the arc remains steady. Preheating can also help reduce the cooling rate in some cases by reducing the temperature gradient between the weld area and the base material.^[21] K value redirects here. ...

Safety

Gas metal arc welding can be dangerous if proper precautions are not taken. Since GMAW employs an electric arc, welders wear protective clothing, including heavy leather gloves and protective long sleeve jackets, to avoid exposure to extreme heat and flames. In addition, the brightness of the electric arc can cause arc eye, in which ultraviolet light causes the inflammation of the cornea and can burn the retinas of the eyes. Helmets with dark face plates are worn to prevent this exposure, and in recent years, new helmet models have been produced that feature a liquid crystal-type face plate that self-darkens upon exposure to high amounts of UV light. Transparent welding curtains, made of a polyvinyl chloride plastic film, are often used to shield nearby workers and bystanders from exposure to the UV light from the electric arc.^[22] A welder is a tradesman who specialises in welding materials together. ... Protective clothing is clothing designed to protect either the wearers body or other items of clothing from hazards such as heat, chemicals and infection. ... For people named Leather, see Leather (surname). ... // Leather gloves A glove (Middle English from Old English glof) is a type of garment (and more specifically a fashion accessory) which covers the hand of a human. ... Arc eye, also known as arc flash, welders flash, corneal flash burns, or flash burns, is a painful ocular condition sometimes experienced by welders who have failed to use adequate eye protection. ... For other uses, see Ultraviolet (disambiguation). ... The cornea is the transparent front part of the eye that covers the iris, pupil, and anterior chamber, providing most of an eyes optical power [1]. Together with the lens, the cornea refracts light and, as a result, helps the eye to focus. ... Human eye cross-sectional view. ... A person wearing a helmet. ... Schlieren texture of Liquid Crystal nematic phase Liquid crystals are substances that exhibit a phase of matter that has properties between those of a conventional liquid, and those of a solid crystal. ... Polyvinyl chloride Polyvinyl chloride, (IUPAC Polychloroethene) commonly abbreviated PVC, is a widely used thermoplastic polymer. ...

Welders are also often exposed to dangerous gases and particulate matter. GMAW produces smoke containing particles of various types of oxides, and the size of the particles in question tends to influence the toxicity of the fumes, with smaller particles presenting a greater danger. Additionally, carbon dioxide and ozone gases can prove dangerous if ventilation is inadequate. Furthermore, because the use of compressed gases in GMAW pose an explosion and fire risk, some common precautions include limiting the amount of oxygen in the air and keeping combustible materials away from the workplace.^[23] While porosity usually results from atmospheric contamination, too much shielding gas has a similar effect; if the flow rate is too high it may create a vortex that draws in the surrounding air, thereby contaminating the weld pool as it cools. The gas output should be felt (as a cool breeze) on a dry hand but not enough to create any noticeable pressure, this equates to between 20–25 psi (mild and stainless steel). Above 26 volts the gas debit should be augmented slightly since the weld pool takes longer to cool. As a factor that is often ignored, many flow meters are never adjusted and typically run between 35–45 psi. A healthy reduction of gas will not affect the quality of the weld, will save money on shielding gas and reduce the rate at which the tank must be replaced. Particulates, alternatively referred to as particulate matter (PM), aerosols or fine particles, are tiny particles of solid or liquid suspended in a gas. ... This article does not cite any references or sources. ... An oxide is a chemical compound containing at least one oxygen atom and other elements. ... Toxic redirects here, but this is also the name of a song by Britney Spears; see Toxic (song) Look up toxic and toxicity in Wiktionary, the free dictionary. ... Carbon dioxide is a chemical compound composed of two oxygen atoms covalently bonded to a single carbon atom. ... For other uses, see Ozone (disambiguation). ...

Metal transfer modes

Globular

GMAW with globular metal transfer is often considered the most undesirable of the four major GMAW variations, because of its tendency to produce high heat, a poor weld surface, and spatter. The method was originally developed as a cost efficient way to weld steel using GMAW, because this variation uses carbon dioxide, a less expensive shielding gas than argon. Adding to its economic advantage was its high deposition rate, allowing welding speeds of up to 110 mm/s (250 in/min).^[24] As the weld is made, a ball of molten metal from the electrode tends to build up on the end of the electrode, often in irregular shapes with a larger diameter than the electrode itself. When the droplet finally detaches either by gravity or short circuiting, it falls to the workpiece, leaving an uneven surface and often causing spatter.^[25] As a result of the large molten droplet, the process is generally limited to flat and horizontal welding positions. The high amount of heat generated also is a downside, because it forces the welder to use a larger electrode wire, increases the size of the weld pool, and causes greater residual stresses and distortion in the weld area.

Short-circuiting

Further developments in welding steel with GMAW led to a variation known as short-circuiting or short-arc GMAW, in which carbon dioxide shields the weld, the electrode wire is smaller, and the current is lower than for the globular method. As a result of the lower current, the heat input for the short-arc variation is reduced, making it possible to weld thinner materials while decreasing the amount of distortion and residual stress in the weld area. As in globular welding, molten droplets form on the tip of the electrode, but instead of dropping to the weld pool, they bridge the gap between the electrode and the weld pool as a result of the greater wire feed rate. This causes a short circuit and extinguishes the arc, but it is quickly reignited after the surface tension of the weld pool pulls the molten metal bead off the electrode tip. This process is repeated about 100 times per second, making the arc appear constant to the human eye. This type of metal transfer provides better weld quality and less spatter than the globular variation, and allows for welding in all positions, albeit with slower deposition of weld material. Setting the weld process parameters (volts, amps and wire feed rate) within a relatively narrow band is critical to maintaining a stable arc: generally less than 200 amps and 22 volts for most applications.^[26] Like the globular variation, it can only be used on ferrous metals.^[27] For alternate meanings see Short circuit (disambiguation) A short circuit (sometimes known as simply a short) is a fault whereby electricity moves through a circuit in an unintended path, usually due to a connection forming where none was expected. ... Surface tension is an effect within the surface layer of a liquid that causes that layer to behave as an elastic sheet. ...

Spray

Spray transfer GMAW was the first metal transfer method used in GMAW, and well-suited to welding aluminum and stainless steel while employing an inert shielding gas. In this GMAW process, the weld electrode metal is rapidly passed along the stable electric arc from the electrode to the workpiece, essentially eliminating spatter and resulting in a high-quality weld finish. As the current and voltage increases beyond the range of short circuit transfer the weld electrode metal transfer transitions from larger globules through small droplets to a vaporized stream at the highest energies.^[28] Since this vaporized spray transfer variation of the GMAW weld process requires higher voltage and current than short circuit transfer, and as a result of the higher heat input and larger weld pool area (for a given weld electrode diameter), it is generally used only on workpieces of thicknesses above about 6.4 mm (0.25 in).^[29] Also, because of the large weld pool, it is often limited to flat and horizontal welding positions and sometimes also used for vertical-down welds. It is generally not practical for root pass welds.^[30] When a smaller electrode is used in conjunction with lower heat input, its versatility increases. The maximum deposition rate for spray arc GMAW is relatively high; about 60 mm/s (150 in/min).^[31]

Pulsed-spray

A more recently developed method, the pulse-spray metal transfer mode is based on the principles of spray transfer but uses a pulsing current to melt the filler wire and allow one small molten droplet to fall with each pulse. The pulses allow the average current to be lower, decreasing the overall heat input and thereby decreasing the size of the weld pool and heat-affected zone while making it possible to weld thin workpieces. The pulse provides a stable arc and no spatter, since no short-circuiting takes place. This also makes the process suitable for nearly all metals, and thicker electrode wire can be used as well. The smaller weld pool gives the variation greater versatility, making it possible to weld in all positions. In comparison with short arc GMAW, this method has a somewhat slower maximum speed (85 mm/s or 200 in/min) and the process also requires that the shielding gas be primarily argon with a low carbon dioxide concentration. Additionally, it requires a special power source capable of providing current pulses with a frequency between 30 and 400 pulses per second. However, the method has gained popularity, since it requires lower heat input and can be used to weld thin workpieces, as well as nonferrous materials.^[32]

References

This article is about the U.S. state. ... Cleveland redirects here. ... is the 201st day of the year (202nd in leap years) in the Gregorian calendar. ... Year 2005 (MMV) was a common year starting on Saturday (link displays full calendar) of the Gregorian calendar. ... Nickname: Motto: Urbs in Horto (Latin: City in a Garden), I Will Location in the Chicago metro area and Illinois Coordinates: , Country State Counties Cook, DuPage Settled 1770s Incorporated March 4, 1837 Government - Mayor Richard M. Daley (D) Area - City 234. ...

Notes

Contents

Development

Equipment

Welding gun and wire feed unit

Power supply

Electrode

Shielding gas

Operation

Technique

Quality

Safety

Metal transfer modes

Globular

Short-circuiting

Spray

Pulsed-spray

References

Notes

Further reading

External links

Contents

Development GA_googleFillSlot("encyclopedia_square");

Equipment

Welding gun and wire feed unit

Power supply

Electrode

Shielding gas

Operation

Technique

Quality

Safety

Metal transfer modes

Globular

Short-circuiting

Spray

Pulsed-spray

References

Notes

Further reading

External links

Development