| This article needs additional references or sources for verification.
Please help improve this article by adding reliable references. (help, get involved!)
Unverifiable material may be challenged and removed. | A loudspeaker enclosure is a cabinet designed to transmit sound to the listener via mounted loudspeaker drive units. The major role of the enclosure is to prevent the out of phase sound waves from the rear of the speaker from combining with the 'in phase' sound waves from the front of the speaker. This results in interference patterns and cancellation, causing the efficiency of the speaker to be reduced, particularly in the low frequencies where the wavelengths are large enough that interference will affect the entire listening area. This article is about a portion of a periodic process. ...
Interference of two circular waves - Wavelength (decreasing bottom to top) and Wave centers distance (increasing to the right). ...
History Before the 1950s many manufacturers did not fully enclose their loudspeaker cabinets; the back of the cabinet was typically left open. This was done for several reasons, not least because electronics (then always hot tube equipment) could be placed inside and, if the enclosure were open, could be cooled by convection. Early on, it was observed that the enclosure had a strong effect on the bass response of the speaker. An engineer at Bell Labs even patented a primitive ported enclosure design. Since the rear of the loudspeaker radiates soundwaves 180 degrees out of phase from the front, there will be constructive and destructive interference for loudspeakers without enclosures, and below some frequencies, in open baffled loudspeakers. This causes loss of bass and comb filtering (i.e. response peaks and dips in power regardless of the signal meant to be reproduced). Most of the enclosure types discussed in this article were invented to either wall off the out of phase sound from one side of the driver, or to modify it so that it could be used to enhance the sound produced from the other side. Bell Laboratories (also known as Bell Labs and formerly known as AT&T Bell Laboratories and Bell Telephone Laboratories) was the main research and development arm of the United States Bell System. ...
Background In some respects, the ideal mounting for a low frequency loudspeaker driver would be an inert flat panel of infinite size with infinite space behind it. This would entirely prevent the rear soundwaves from interference (i.e. comb filter cancellations) with the soundwaves from the front. An "open baffle" loudspeaker is an approximation of this, since the driver is mounted on a panel, hopefully of size comparable to the lowest wavelength to be reproduced. In either case, the driver would have to have a relatively stiff suspension to provide the restoring force which might have been provided at low frequencies by a smaller enclosure, so only some drivers are suitable for this kind of mounting. However, for most purposes this is impractical and enclosures must use other techniques. A transducer is a device, usually electrical or electronic, that converts one type of energy to another. ...
The wavelength is the distance between repeating units of a wave pattern. ...
Most loudspeaker cabinets use some sort of structure (usually a box) to contain the out of phase sound energy. the box is characteristically made of wood or, more recently, plastic, both for reasons of ease of construction and appearance.
Loudspeaker cabinets are sometimes "sealed" and sometimes "ported". Ported cabinets allow some of the sound energy inside the cabinet to be released, and if designed correctly with proper attention to phase relationships, both increase bass response and reduce driver excursion. Many other engineering variations on the basic box design exist, such as acoustic transmission lines. To meet Wikipedias quality standards, this article may require cleanup. ...
Enclosures always play a significant role in sound production in addition to the intended design effects, adding unfortunate resonances, diffraction, and other unwanted phenomena. Problems with resonance are usually reduced by increasing enclosure mass and/or rigidity, by increased damping of enclosure walls, or by adding absorption internally. In the past, one speaker manufacturer (Wharfedale) even addressed the problem of cabinet resonance by using two wooden panels with the space between filled with sand. Home experimenters have designed speakers built from concrete sewer pipe, and other exotic materials for similar reasons. This article is about resonance in physics. ...
The intensity pattern formed on a screen by diffraction from a square aperture Diffraction refers to various phenomena associated with wave propagation, such as the bending, spreading and interference of waves passing by an object or aperture that disrupts the wave. ...
Wharfedale is the name of a prominent audio equipment manufacturer from the U.K., famous for its loudspeakers. ...
For other uses, see Sand (disambiguation). ...
This article is about the construction material. ...
A sewer is an artificial conduit or system of conduits used to remove sewage (human liquid waste) and to provide drainage. ...
Many diffraction problems, above the lowest frequencies, can be addressed by the shape of the enclosure, avoiding sharp corners on the front of the enclosure, for instance. Experimental research from the 1930s by Dr. H.F. Olsen showed that curved loudspeaker baffles reduce response deviations due to soundwave diffraction, although his research did not show that careful placement of a speaker on even a sharp-edged baffle can minimize diffraction-caused response changes; this was discovered later. Sometimes the differences in phase response at frequencies shared by different drivers can be addressed by adjusting the vertical location of the smaller drivers (usually backwards), or by leaning or stepping the front baffle, so that the wavefront from all drivers is coherent, at and around the crossover frequencies, when sound leaves the cabinet. The acoustic center of the driver—the physical position of the front of each driver's voice coil—dictates the amount of rearward offset needed to "time-align" the drivers. Coherence is from Latin cohaerere = stick together, to be connected with). ...
Woofer and subwoofer enclosures Enclosures used for woofers and subwoofers can be adequately modelled in the low frequency region (approximately 100–200 Hz and below) using acoustics and the lumped component model. Electrical filter theory has been used with considerable success (see Thiele/Small for details). For the purposes of this type of analysis, each enclosure has a loudspeaker topology. The most common enclosure types are listed below. A Sony 9 inch woofer Woofer is the term for a loudspeaker driver that is designed to produce low frequency sounds, typically from around 40 hertz up to a few hundred hertz. ...
a 12 subwoofer driver A subwoofer refers to either a driver, or a complete loudspeaker dedicated to the reproduction of bass audio frequencies, typically from 150 Hz down to 20 Hz. ...
Acoustics is a branch of physics and is the study of sound (mechanical waves in gases, liquids, and solids). ...
This article or section cites very few or no references or sources. ...
Thiele/Small commonly refers to a set of standard parameters that define how a loudspeaker driver performs. ...
Closed-box enclosures Image File history File links Please see the file description page for further information. ...
Image File history File links Please see the file description page for further information. ...
Infinite baffle A variation on the 'open baffle' is to mount the loudspeaker in a very large sealed enclosure. The loudspeaker driver's mass and compliance, (i.e., the stiffness of the cone suspension) determines the driver's resonant frequency, and the damping properties of the system, both affect the low-frequency response of the speaker system. Output falls off below the cabinet resonant frequency (Fs), which can be determined by finding the peak impedance. The designer must balance bass response, flatness of frequency response, efficiency, and size of enclosure. The larger the resonant peak in the bass, the lower the speaker will reproduce its input evenly. But many feel that the resulting low frequency performance of such speakers is over-emphasized. Such enclosures must be large enough that the internal pressure reflections and resonances caused when the driver cone moves backwards into the cabinet does not rise too high and affect the cone's motion. The enclosure is usually filled loosely with foam, pillow stuffing, long fibre wool, fiberglass, or other wadding, converting some of the speaker's thermodynamic properties from adiabatic to isothermal. Compliance can mean: Compliance (medicine), a patients (or doctors) adherence to a recommended course of treatment Compliance (physiology), a measure of stiffness in mechanical science and physiology Compliance (regulation), the act of adhering to, and demonstrating adherence to laws, regulations or policies, in management Category: ...
This article is about resonance in physics. ...
Damping is any effect, either deliberately engendered or inherent to a system, that tends to reduce the amplitude of oscillations of an oscillatory system. ...
Thermodynamics (Greek: thermos = heat and dynamic = change) is the physics of energy, heat, work, entropy and the spontaneity of processes. ...
In thermodynamics, an adiabatic process or an isocaloric process is a thermodynamic process in which no heat is transferred to or from the working fluid. ...
An isothermal process is a thermodynamic process in which the temperature of the system stays constant; ΔT = 0. ...
Today, infinite baffle subwoofers are mostly custom-designed and built components. See page 38 of the February 2007 issue of affordableaudio.org http://www.affordableaudio.org/ e-zine for an example, or see the website for the cult of the infinitely baffled.
Acoustic suspension The closed-box or "acoustic suspension" enclosure, rather than using a large enclosure to avoid the effects of internal air pressure changes caused by cone motion, uses a smaller sealed enclosure, generally much smaller. The enclosure must have a very small leak so internal and external pressures can slowly equalise over time, allowing the speaker to adjust to changes in barometric pressure or altitude. Atmospheric pressure is the pressure caused by the weight of air above any area in the Earths atmosphere. ...
The "spring" suspension that restores the cone to a neutral position is a combination of a relatively soft mechanical suspension of the low frequncy driver and mostly of the air inside the enclosure. At audible frequencies, the air pressure caused by the cone motion is the dominant force. Damping materials such as fiberglass are typically added to the enclosure to shape system performance (i.e. damp) the driver/air volume resonance, and to absorb output (especially in the midrange) from the rear of the diaphragm. An important advantage of a proper acoustic suspension design is that air is a more linear spring than is any practical mechanical cone suspension (i.e. cone surround and spider together) -- they are inherently non-linear in many respects. This improved linearity giving acoustic suspension designs lower distortion than infinite baffle designs, particularly at the lower frequencies and higher power levels at which cone excursion is large. The drawback of these speakers is their low efficiency, due to the loss of the power absorbed inside the cabinet, combined with generally reduced transient response at low frequencies.
Reflex enclosures
Bass-reflex -
Other types of enclosures attempt to improve the low frequency response, or overall efficiency of the loudspeaker, or reduce the size of an enclosure, by using various combinations of cabinet openings or passive radiating elements to transmit low frequency energy from the rear of the speaker to the listener. These enclosures are also referred to as vented, ported or bass reflex enclosures. Their interiors are typically lined with matting (eg, fiberglass) for some of the same reasons as the sealed box speakers above, however, the entire volume is not stuffed with absorbent for two reasons. Air must flow into and out of the port, and carrying bits of stuffing out the port is rarely acceptable. Reflex ports are tuned by their diameter, length, and to some extent shape, all of which affect the mass and motion of the air within the vent and so the behavior of the driver and the sound the system produces. This enclosure type is very commonly used as it lends itself to smaller size and reasonable bass when tuned properly. These enclosures are relatively well understood, at least for low frequency performance, based on work by Thiele and Small who applied electrical filter theory to the acoustic behavior of speakers in enclosures. Bass reflex enclosure schematic (cross-section). ...
Image File history File links Please see the file description page for further information. ...
Image File history File links Please see the file description page for further information. ...
Reflex port is the distinctive feature of a very popular variety of loudspeaker enclosures (bass reflex) which enhances the reproduction of the lowest frequencies generated by the woofer. ...
Bass reflex enclosure schematic (cross-section). ...
Passive radiator -
 Passive radiator enclosure A passive radiator speaker uses a second "passive" driver, or drone, to produce similar low frequency extension or efficiency increase or enclosure size reduction as do ported enclosures. In theory, such enclosures are variations of the bass reflex type, but with the advantage of avoiding a relatively small port or tube through which air moves, sometimes noisily. As well, tuning adjustments for a passive radiator are usually much easier. And with the disadvantage that a passive radiator requires precision construction quite like driver design, thus increasing costs. Passive radiator enclosure with front mounted passive radiator; back or side mounting is also used A speaker enclosure using a passive radiator usually contains an active, or main driver, and a passive cone (or drone or passive radiator). ...
Image File history File links Passive_radiator_enclosure. ...
Image File history File links Passive_radiator_enclosure. ...
Passive radiator enclosure with front mounted passive radiator; back or side mounting is also used A speaker enclosure using a passive radiator usually contains an active, or main driver, and a passive cone (or drone or passive radiator). ...
Compound or Band-pass
Compound or 4 th order band-pass enclosure. A 4th order bandpass is very similar to a vented box in which the contribution from the driver is trapped in a sealed box which modifies the resonance of the driver. In its simplest form it has two chambers. The dividing wall between the chambers has the driver mounted on it and the panel opposite it (or the chamber into which the driver faces) is ported. Image File history File links Bandpass_enclosure. ...
Image File history File links Bandpass_enclosure. ...
If the enclosure on each side of the woofer has a port in it then the enclosure yields a 6th order band-pass response. This enclosure is considerably harder to design and tends to be very senstiive to the characteristics of the driver. As in other reflex enclosures, the ports may be replaced by passive radiators if desired.
Other enclosure types
Dipole
Dipole speakers and their radiation pattern. -
A dipole enclosure in its simplest form is a driver located on a flat baffle panel. The baffle is sometimes folded to reduce its apparent size. A rectangular cross-section is more common than a circular one since it is easier to fabricate in a folded form than a circular one. The baffle dimensions are typically chosen to obtain a particular low frequency response, with larger dimensions giving a lower frequency before the front and rear waves interfere with each other. A dipole enclosure has a "figure-of-eight" radiation pattern, which means that there is a reduction in sound pressure, or loudness, at the sides as compared to the front and rear. This is useful if it can be used to prevent the sound from being as loud in some places than in others. Image File history File links Dipole_speaker. ...
Image File history File links Dipole_speaker. ...
Dipole speakers and their radiation pattern. ...
Horn
 Horn loudspeaker schematic. -
A horn speaker is a speaker system using a "horn" to match the driver cone to the air. The horn itself does not amplify, but rather improves the coupling between the speaker driver (typically made of paper or, more recently, more exotic materials such as titanium) and the air (which has a very low density). The motional characteristics of air and speaker cones (whatever the material) are quite different; properly designed horns have the effect of making the speaker cone transfer more of the electrical energy in the voice coil into the air. The driver in effect appears to have a large surface area. In addition, horns can help control dispersion at higher frequencies which is useful in some applications such as sound reinforcement. Image File history File links Horn_speaker. ...
Horn loudspeaker with a sealed box driver mounting A horn speaker is a loudspeaker which uses a horn to increase the overall efficiency of the driving element, typically a diaphragm driven by an electromagnet. ...
This article or section needs copy editing for grammar, style, cohesion, tone and/or spelling. ...
A horn is a tapered sound-guide designed to provide an acoustic impedance match between a sound-producing device and the characteristic impedance of free space. ...
General Name, symbol, number titanium, Ti, 22 Chemical series transition metals Group, period, block 4, 4, d Appearance silvery metallic Standard atomic weight 47. ...
For other uses, see Density (disambiguation). ...
The mathematical theory of horn coupling is well developed and understood, even if implementation is difficult in the real world. Proper horns for high frequencies are small (above say 3kHz or so, a few inches), those for midrange frequencies (perhaps 300H to 2KHz) much larger, perhaps 1 or 2 feet, and for low frequencies (under 300Hz) very large, dozens of feet. Various speaker manufactures have produced folded low frequency horns which are much smaller (e.g., Altec Lansing, JBL, Klipsch, Lowther, Tannoy) and can actually hope to fit in real rooms. These are necessarily compromises, and because they are physically complex, they are expensive. Some of these speakers are very well thought of. In earlier times, some users built horns whose mouths were built into the walls of listening rooms.
Multiple entry horn The multiple entry horn (known variously as Coentrant horn, Unity horn or Synergy horn) incorporates several drivers ported into the horn at stepped distances from the horn's apex, where the high frequency driver is placed. This design offers a marked increase in transient response as each of the drivers is aligned in phase and time and exiting out of the same horn mouth. Another benefit is the uniform radiation pattern throughout its frequency range. Uniform pattern allows smooth arraying of multiple enclosures.[1] Image File history File links Size of this preview: 757 × 599 pixelsFull resolution (806 × 638 pixel, file size: 222 KB, MIME type: image/png) I, the copyright holder of this work, hereby grant the permission to copy, distribute and/or modify this document under the terms of the GNU Free...
Image File history File links Size of this preview: 757 × 599 pixelsFull resolution (806 × 638 pixel, file size: 222 KB, MIME type: image/png) I, the copyright holder of this work, hereby grant the permission to copy, distribute and/or modify this document under the terms of the GNU Free...
Tapped horn Both sides of a long-excursion high-power driver in a tapped horn enclosure are ported into the horn itself, with one path length long and the other short. These two paths combine in phase at the horn's mouth within the frequency range of interest. This new design is especially effective at subwoofer frequencies and offers reductions in enclosure size along with more output power and less distortion.[1]
Transmission line
 Transmission line enclosure. A transmission line enclosure is a waveguide in which the structure shifts the phase of the driver's rear output by at least 90°, thereby reinforcing the frequencies near the driver's Fs. Transmission lines tend to be larger than ported enclosures, due to the size and length of the guide required (typically 1/4th the longest wavelength of interest). The design is often described as non-resonant, and some designs are sufficiently stuffed with absorbent material that there is indeed not much output from the line's port. But it is the inherent resonance (typically at 1/4 wavelength) that can enhance the bass response in this type of enclosure, albeit with less absorbent stuffing. Among the first examples of this enclosure design approach were the projects published in Wireless World by Bailey in the early 1970s. A variation on the transmission line enclosure utilizes a tapered tube, with the terminus (opening/port) having a smaller area than the throat. The tapering tube can be coiled for lower frequency driver enclosures to reduce the dimensions of the speaker resulting in a seashell like appearance. Most notably Bowers & Wilkins have used this approach in their flagship Nautilus speaker as well as the use of smaller straight tapering tubes in many of their other lines. Image File history File links No higher resolution available. ...
Image File history File links No higher resolution available. ...
Thiele/Small commonly refers to a set of standard parameters that define how a loudspeaker driver performs. ...
Bowers & Wilkins is a high-end British loudspeaker company that produces reference quality hi-fi and home theatre speakers. ...
Recently, numerical simulations by several researchers (eg, George Augspurger and Martin J. King) have brought a degree of order to the theory and practical design of these systems.[citation needed]
Tapered quarter-wave pipe The tapered quarter-wave pipe (TQWP) is an example of a combination of transmission line and horn effects. It is highly regarded by some speaker designers. The concept is that the sound emitted from the rear of the loudspeaker driver is progressively reflected and absorbed along the length of the tapering tube, almost completely preventing internally reflected sound being retransmitted through the cone of the loudspeaker. The lower part of the pipe acts as a horn while the top can be visualised as an extended compression chamber. The entire pipe can also be seen as a tapered transmission line in inverted form. (A traditional tapered transmission line, confusingly also sometimes referred to as a TQWP, has a smaller mouth area than throat area.) Its relatively low adoption in commercial speakers can mostly be attributed to the large resulting dimensions of the speaker produced and the expense of manufacturing a rigid tapering tube. The TQWP is also known as a Voigt pipe and was designed by P.G.A.H. Voigt, the main Lowther driver designer. The Voigt pipe is a type of loudspeaker enclosure that embodies a combination of transmission line, ported enclosure and horn characteristics. ...
Aperiodic enclosures There is another design which falls between transmission lines and bass reflex enclosures. By setting up a port, and then blocking it precisely with sufficiently tightly packed fiber filling, it's possible to adjust the damping in the port as desired. The result is control of the resonance behavior of the system which improves low frequency reproduction, according to some designers. Dynaco was the primary producer of these enclosures for many years. The design remains uncommon among commercial designs currently available. A reason for this may be that adding damping material reduces the efficiency of the system; the same alignment can be achieved by simply choosing a loudspeaker driver with the appropriate parameters and tuning the enclosure and port for the desired response. Dynaco is an American hi-fi manufacturer founded by David Hafler and Ed Laurent in 1955. ...
Thiele/Small commonly refers to a set of standard parameters that define how a loudspeaker driver performs. ...
A similar technique has been used in aftermarket car audio; it is called "aperiodic membrane" (AP). A resistive mat is placed in front of or directly behind the loudspeaker driver (usually mounted on the rear deck of the car in order to use the trunk as an enclosure). The loudspeaker driver is sealed to the mat so that all acoustic output in one direction must pass through the mat. This increases mechanical damping, and the resulting decrease in the impedance magnitude at resonance is generally the desired effect, though there is no perceived or objective benefit to this. Again, this technique reduces efficiency and the same result can be achieved through selection of a loudspeaker driver with a lower Q factor, or even equalization. This is reinforced by the purveyors of AP membranes; they are often sold with an electronic processor which, via equalization, restores the bass output lost through the mechanical damping. The effect of the equalization is opposite to that of the AP membrane, resulting in a loss of damping and an effective response similar to that of the loudspeaker without the aperiodic membrane and electronic processor. It has been suggested that In car entertainment be merged into this article or section. ...
This article is about resonance in physics. ...
This article or section does not cite any references or sources. ...
For information about computer bandwidth management, see Equalization (computing). ...
See also Cross-section of a full-range loudspeaker. ...
This article or section needs copy editing for grammar, style, cohesion, tone and/or spelling. ...
A midrange speaker A loudspeaker driver that produces the frequency range from approximately 300–5000 hertz is known as a mid-range. ...
a 12 subwoofer driver A subwoofer refers to either a driver, or a complete loudspeaker dedicated to the reproduction of bass audio frequencies, typically from 150 Hz down to 20 Hz. ...
A shielded Peerless v-line dome tweeter A tweeter is a driver designed to produce high frequencies, typically from around 2,000 hertz to 20,000 hertz (20,000 Hz is generally considered to be the upper limit of the human ear). ...
A Sony 9 inch woofer Woofer is the term for a loudspeaker driver that is designed to produce low frequency sounds, typically from around 40 hertz up to a few hundred hertz. ...
A guitar speaker cabinet contains one or more guitar speakers - usually 1, 2, or 4 speakers, most commonly 12 in diameter. ...
Notes
External links |
Feeds |
Contact