Promotional image for Pontiac's all new 287 in³, dubbed the "Strato-Streak"

From 1955 to 1981 the Pontiac Division of General Motors manufactured its own, unique V8 engines. Displacement began at 287 in³ and grew as large as 455 in³ (7.5 L) by 1970. This article is about Pontiac automobiles; for the Native American leader, see Chief Pontiac, for other uses see the Pontiac (disambiguation). ... General Motors Corporation (NYSE: GM), also known as GM, is an American automobile maker with worldwide operations and brands including Buick, Cadillac, Chevrolet, GMC, Holden, Hummer, Opel, Pontiac, Saturn, Saab and Vauxhall. ... The Liberty V8 aircraft engine clearly shows the configuration A V8 engine is a V engine with eight cylinders. ...

An engine of intermediate size (neither a true small-block nor big-block), the Pontiac V8 was a unique design, distinct from Buick, Chevrolet, or Oldsmobile engines. For other uses of the term, see Small block (disambiguation). ... A big-block engine is a North American V8 in a family of engines which generally have greater than 6 litres (360 cubic inches) of displacement; factory engine sizes reached a peak of 8. ... Buick is a brand of automobile built in the United States, Canada, China and in Spain by General Motors Corporation. ... Chevrolet (IPA: - French origin) (colloquially Chevy) is a brand of automobile, produced by General Motors (GM). ... Oldsmobile is a brand of automobile produced for most of its existence by General Motors. ...

Pontiac's engines were used in its U.S.-market cars; Canadian Pontiacs generally used Chevrolet engines. From 1955 through 1959 Pontiac's V8 was also used in GMC pick-up trucks. For other uses, see United States (disambiguation) and US (disambiguation). ... Main articles: History of Canada, Timeline of Canadian history Canada has been inhabited by aboriginal peoples (known in Canada as First Nations) for at least 40,000 years. ... Chevrolet (IPA: - French origin) (colloquially Chevy) is a brand of automobile, produced by General Motors (GM). ... GMC, formerly known as GMC Truck, is a brand name used on trucks, vans, and SUVs marketed in North America and the Middle East by General Motors. ... Pickup truck with extended cabin and homebuilt lumber rack. ...

History

The development of Pontiac's OHV V8 dates back to 1946, when engineers began considering new engine designs for postwar cars. Despite these experiments, the division's conservative management saw no immediate need to replace the Pontiac Straight-8 engine, which had served well since 1933. When Robert Critchfield took over as general manager in 1952, however, he launched an ambitious plan to move Pontiac into the upscale, mid-range market segment occupied by Oldsmobile, and that demanded V8 power. The development of the new engine was fast-tracked, but since its relatively late development let it take advantage of the experience gained in the Oldsmobile V8 engine and Cadillac V8 engine, it was remarkably free of teething problems. The main unique feature of the Pontiac engine was the stamped rocker-arm system, which had been devised by Pontiac engineer Clayton Leach in 1948. At the request of Ed Cole, general manager of Chevrolet, the layout was also used by the Chevrolet V8 released in 1955, an exception to the customary GM policy of allowing a division one year of exclusive use of an internally developed advance. Like many other American automobile makers, Pontiac produced a straight-8 engine. ... A Market segment is a subgroup of people or organizations sharing one or more characteristics that cause them to have similar product needs. ... Oldsmobile is a brand of automobile produced for most of its existence by General Motors. ... This article does not cite any references or sources. ... Cadillac was the first automobile maker to mass produce a V8 engine. ... Edward Nicholas Cole Born September 17, 1909 in Marne, Michigan. ... Chevrolet (IPA: - French origin) (colloquially Chevy) is a brand of automobile, produced by General Motors (GM). ...

Federal emissions standards and the drive towards "corporate" engines shared among all GM divisions led to the progressive demise of the Pontiac V8 in the late 1970s. The last Pontiac V8, a 301, was produced in 1980 for a 1981 automobile.

Pontiac also had a V8 engine used in 1932 only.

Design

The Pontiac V8 was an overhead valve engine with wedge combustion chambers. It used cast iron cylinder heads and a cast-iron block. An unusual design feature was mounting the rocker arms on ball pivots on studs set into the cylinder head, rather than using a separate rocker shaft; this allowed more consistent valve action with less weight than a conventional shaft. All (except the 303 Ram Air V engine and 265 and 301) used 6.625 in (168.3 mm) connecting rods. All Pontiac V8s from 1955 to 1959 were reverse cooled, known as the "gusher" cooling system. It was plagued with corrosion issues and was removed from the design for the 1960 model year due to warranty returns. OHV redirects here. ... A combustion chamber is part of an engine in which fuel is burned. ... Cast iron usually refers to grey cast iron, but can mean any of a group of iron-based alloys containing more than 2% carbon (alloys with less carbon are carbon steel by definition). ... The cylinder head from a GMC van. ... The cylinder block of a Ford I4 DOHC engine The cylinder block or engine block is a machined casting (or sometimes an assembly of modules) containing cylindrically bored holes for the pistons of a multi-cylinder reciprocating internal combustion engine, or for a similarly constructed device such as a pump. ... rocker arm This page meets Wikipedias criteria for speedy deletion. ... Promotional image for Pontiacs all new 287 in³, dubbed the Strato-Streak From 1955 to 1981 the Pontiac Division of General Motors manufactured its own, unique V8 engines. ... piston (top) and connecting rod from typical automotive engine (scale is in centimetres) Components of a typical, four stroke cycle, DOHC piston engine. ...

Most iterations had an overall length (to the edge of the water pump pulley) of 28.25 in, an overall width of 27 in, and a height (not including air cleaner) of 31 in (718 mm × 686 mm × 787 mm). Dry weight ranged from 590 lb to 650 lb (270 to 295 kg), depending on displacement and year. Most Pontiac engines were painted light blue. The 389 version was known as the "Tempest" or "Trophy" V8, depending on year and hp rating. Pontiac was one of a few US manufacturers which did not regularly identify its engine names and sizes with air cleaner or valve cover decals. A pump is a mechanical device used to move liquids or gases. ... On an internal combustion engine, an air cleaner is a device that blocks dirt and debris from entering the induction system, where it might cause internal damage. ...

Engine Development: Small Journal Engines

287

The V8 engine was introduced for the 1955 model year as the "Strato Streak". Not long before the model year introduction, Pontiac management decided that the entire line would be V8-powered. This was based on results of over 1 million test miles which was unheard of at the time.

The 287 was an "oversquare" engine with a bore of 3.75 in (95.25 mm) and a stroke of 3.25 in (82.55 mm), for a total displacement of 287 in³ (4.7 L). Compression ratio was a modest 8.00:1, with valve diameters of 1.781 in (45.2 mm) (intake) and 1.500 in (38.1 mm). It was rated 180 hp (134 kW) @ 4600 rpm and 264 ft·lbf (358 N·m) @ 2400 rpm with a two-barrel carburetor, 200 hp (149 kW) @ 4600 rpm and 278 ft·lbf (377 N·m) @ 2800 rpm with the four-barrel carburetor. Bore may refer to: A wave in a river caused by an incoming tide - see tidal bore The diameter of a pipe or tube, or the caliber of a gun The diameter of a cylinder and piston in a piston engine (See also: Stroke) A person who is boring The... For other uses, see Stroke (disambiguation). ... Bold text The compression ratio is a single number that can be used to predict the performance of any engine (such as an internal-combustion engine or a Stirling Engine). ... Bendix-Technico (Stromberg) 1-barrel downdraft carburetor model BXUV-3, with nomenclature A carburetor (North American spelling) or carburettor (Commonwealth spelling), is a device that blends air and fuel for an internal combustion engine. ...

316

For 1956 the V8 was bored out to 3.9375 in (100.0 mm), increasing displacement to 316 in³ (5.2 L). It was offered in the following forms:

(with manual transmission)

• two-barrel carburetor, 7.9:1 compression, 192 hp (143 kW) @ 4400 rpm, 297 ft·lbf (403 N·m) @ 2800 rpm
• four-barrel carburetor, 8.9:1 compression, 216 hp (161 kW) @ 4800 rpm, 315 ft·lbf (427 N·m) @ 2800 rpm

(with Hydramatic) Hydramatic (also known as Hydra-Matic) was an automatic transmission developed by General Motorss Oldsmobile division. ...

• two-barrel carburetor, 8.9:1 compression, 205 hp (153 kW) @ 4600 rpm, 294 ft·lbf (399 N·m) @ 2600 rpm
• four-barrel carburetor, 8.9:1 compression, 227 hp (169 kW) @ 4800 rpm, 312 ft·lbf (423 N·m) @ 3000 rpm
• two four-barrel carburetors, 10.5:1 compression, 285 hp (213 kW) @ 5100 rpm, 330 ft·lbf (447 N·m) @ 2600 rpm.

336

The 336 in³ (5.5 L) engine was only used in GMC trucks. The bore was 3.875 (98.4 mm) and the stroke was 3.56 in. (90.4 mm).

347

Pontiac V8 engine with Tripower carb setup

For 1957 the V8's stroke was increased to 3.56 in (90.4 mm), for a displacement of 347 in³ (5.7 L). For the first time, Pontiac offered Tri-Power, three two-barrel carburetors with a sequential linkage (replacing the previous dual-quad set-up). Power ratings increased accordingly: Download high resolution version (1788x1524, 581 KB)Pontiac V8 with Tripower carb setup. ... Download high resolution version (1788x1524, 581 KB)Pontiac V8 with Tripower carb setup. ...

(with manual transmission)

• two-barrel carburetor, 8.5:1 compression, 227 hp (169 kW) @ 4600 rpm, 333 ft·lbf (451 N·m) @ 2300 rpm
• four-barrel carburetor, 10:1 compression, 244 hp (182 kW) @ 4800 rpm, 350 ft·lbf (475 N·m) @ 2600 rpm

(with Hydramatic) Hydramatic (also known as Hydra-Matic) was an automatic transmission developed by General Motorss Oldsmobile division. ...

• two-barrel carburetor, 10.0:1 compression, 244 hp (182 kW) @ 4800 rpm, 350 ft·lbf (475 N·m) @ 2600 rpm
• four-barrel carburetor, 10.0:1 compression, 270 hp (201 kW) @ 4800 rpm, 359 ft·lbf (487 N·m) @ 2900 rpm
• three two-barrel carburetors, 10.00:1 compression, 290 hp (216 kW) @ 5000 rpm, 375 ft·lbf (508 N·m) @ 2800 rpm.

Several dealer-installed camshafts were optional to increase power further to 310 hp (231 kW). For the fictional characters of the same name, see Camshaft (Transformers). ...

Standard only for the Pontiac Bonneville was Pontiac's first-ever fuel injection system. A mechanical system built by Rochester, it was similar in principle, but not identical, to the contemporary Chevrolet "fuelie". Pontiac did not release official power ratings for this engine, saying only that it had more than 300 hp (220 kW). Contemporary road tests suggest that it was actually somewhat inferior to the Tri-Power engines, although it did have better fuel economy. Only 630 Bonnevilles were produced for 1957, all of them fuel-injected. The Pontiac Bonneville is an automobile built by the Pontiac division of General Motors from 1958 to 2005. ... // Fuel injection is a system of fuel delivery for mixture with air in an internal combustion engine. ... Rochester Products Division was a division of General Motors that manufactured carburetors, and related components including emissions control devices and cruise control systems. ...

370

For 1958 the V8's bore was increased again to 4.06 in (103.2 mm), increasing displacement to 370 in³ (6.1 L).

The fuel-injected engine was now an option, not standard, on the Bonneville, carrying a staggering price tag of $500 (almost 15% of the car's base price). It was rated at 310 hp (231 kW) @ 4800 rpm and 400 ft·lbf (542 N·m) @ 3,000 rpm on 10.5:1 compression. Only about 400 were produced before the fuel injection system was quietly dropped.

389

For 1959 the V8's stroke was increased to 3.75 in (95.3 mm), raising displacement to 389 in³ (6.4 L). The 389 would remain the standard Pontiac V8 engine through 1966, offered in a bewildering variety of outputs ranging from 215 hp (160 kW) to 360 hp (160 to 269 kW). The 389 was the standard engine for the Pontiac GTO through 1966. 1965 Pontiac GTO convertible The Pontiac GTO was an automobile built by Pontiac from 1964 to 1974, and by General Motors Holden in Australia from 2004 to 2006. ...

326

For 1963 Pontiac dropped the Olds/Buick sourced 215 aluminum V8 it had offered on the Pontiac Tempest and replaced it with a small-bore version of the standard 389 Pontiac V8. It shared the 389's 3.75 in (95.3 mm) stroke, but its bore was reduced to 3.72 in (94.5 mm), giving it a displacement of 326 in³ (5.4 L). It is interesting to note that the very first 1963 326 engines used a 3.78 inch bore size for an actual 336 cubic inch displacement. In 1964 Pontiac reduced the bore size to what was correct for 326 inches of displacement, a 3.72 inch bore. It was rated at 250 hp (193 kW) with 8.6:1 compression and 260 hp (194 kW) at 10.25:1 compression. Both used a single, two-barrel carburetor. The 326 subsequently became the optional V8 engine for Tempests, and later the Pontiac Firebird, through 1967. Like its sister General Motors divisions, Buick produced its own family of V8 engines to replace its straight-8 engines. ... The Pontiac Tempest was an entry-level compact automobile produced by the Pontiac Motor Division of General Motors, introduced in September 1960 for the 1961 model year. ... The Pontiac Firebird was a pony car built by the Pontiac division of General Motors between 1967 and 2002. ...

A higher-output version was offered, called the 326 HO (High Output). It had a four-barrel carb, dual exhausts, and higher compression, and was good for 280 hp (209 kW) for 1963-1965, and 285 hp (213 kW) for 1966 and the final year, 1967.

400

For 1967, Pontiac introduced the 400 in³ (6.6 L).

The '400' V8 was essentially a bored-out 389 with 4.121 inch bore and 3.75 inch stroke (104.7 mm by 95.3 mm). It replaced the 389 in 1967 and remained in production through the 1979 model year.

The 400 was the only engine installed in '67-69 Pontiac GTOs. It was also the biggest engine available in '67-'70 Firebirds. The 400 was a popular performance option for many of Pontiac's cars. The 400 engine produces a good balance of low end torque and higher RPM horsepower.

In 1967 the cylinder head design was improved for all engines. The valve angle was changed for better breathing. 1967 was the last year for closed chambered heads. The "670" head was a '67-only casting, and the last PMD head to have a closed chamber. Pontiac went to open chambered heads in '67 to improve power, engine breathing and emissions. The valve size increased as well, to 2.11" intake and 1.77" exhaust valves on high performance heads. Low performance and 2bbl applications got 1.96" intake and 1.66" exhaust valves and pressed in rocker arm studs.

400s were produced until 1979; this was the final Pontiac V8 based on the 1955 design.

350

In 1968 the 326 was replaced by the 350, which used a 3.875 in bore and 3.75 in stroke for a total displacement of 353.79 in³ although it was still called a 350 (5.7 L).

366

The 366 was never intended for production, it was a variant of the 303, only on a tall (normal) deck sharing Ram Air IV or Ram Air V architecture.

301

See also: Pontiac 301 Turbo

The 301 in³ (4.9 L) 301 was offered from 1977 to 1981. It had a 4.00 inch (101.6 mm) bore and 3.00 inch (76.2 mm) stroke. Based in part on designs for the "short deck" 303 in³ (5.0 L) engine designed for the 1970 racing season, it had a shorter deck than the big V8, and used thin-wall castings to reduce weight. The crankshafts were also unique in the fact that they featured only two counter weights instead of the usual five, and also featured lightened connecting rod journals. This made the so-called small-block Pontiac weigh even less than its Chevrolet small-block counterpart. It produced 135 to 170 hp (97 to 127 kW). The Pontiac 301 EC (Electronic Controls) version offered in 1981 produced 155 hp (116 kW) and 245 lb·ft (332 N·m) of torque, although it's rumored that the actual HP was closer to 170. The 1980 301 Turbo was rated at 210 hp (157 kW) @ 4400 rpm and 345 lb·ft (468 N·m) of torque @ 2800 rpm. The 1981 301 Turbo gained the electronic controls with an O2 sensor, feedback ECM and E4ME Quadrajet providing a slight reduction in power to 205 hp (153 kW) and 340 lb·ft (461 N·m) torque. Although it bears no resemblance to the 1955-vintage powerplants, the 301 has the distinction of being the last true Pontiac motor as Pontiac stopped production of all V8s effective April 1st 1981. The Pontiac 301 turbo engine was an engine that Pontiac put in 1980 and 1981 Trans Ams and Formula Firebirds. ... The Quadrajet is a 4 barrel carburetor made by the Rochester Products Division of GM that was widely used in General Motors motor vehicles until 1990, in which its last application was on the Oldsmobile 307 V8 engine, which was last used in in the Cadillac Brougham and full size...

From 1977-1980 there were 4 distinct 301 versions:

301 2BBL (135 hp), 301 4BBL (150 hp), 301 4BBL 'HO' or 'EC' (170 hp), and the 301 Turbo.

The 301 Turbo was unique in that it had a beefier block than the 77-79 versions (which carried on in the non turbo versions in 1980 and 1981), a very mild camshaft with .350-inch lift and 250 degrees gross duration, a 60 psi oil pump to ensure adequete oil to the oil cooled Garrett TBO-305 Turbocharger, a rolled fillet crankshaft, a fully baffled oil pan, and a specific 800 cfm Quadrajet carburator. This 800 cfm Quadrajet had super rich "DX" secondary metering rods and a remote vacuum source for the primary metering rod enrichment circuit that allowed the "PEVR", Power Enrichment Vacuum Regulator to release the primary metering rods to move to the up position (enrichment) anytime during boosted conditions. This was to ensure that there was enough fuel to cool the cast offset dished pistons. Boost was wastegate limited to 9 psi (+/- 1 psi). The 301 Turbo package mandated Air Conditioning, automatic THM350 non-lockup transmission and 3.08 gears.

The 301 Turbo was limited to Trans Am and Formula Firebird production only. Some literature has indicated that the 301 Turbo may have found its way into the Chevrolet Z28. It is unclear if any were ever produced.

265

Based on the same short-deck as the 301, the 265 (4.3 L) was offered only in 1980 and 1981, and featured a smaller bore of 3.75 in (95.3 mm) coupled with the same 3.00 in (76.2 mm) stroke of the 301. It produced 120 hp (90 kW)

Engine Development: Large Journal Engines

421

Introduced in 1961 as a dealer installed Super Duty option that had dual four barrels, the 421 in³ (6.9 L) was bored to 4.09 in (103.9 mm) and stroked to 4.00 in (101.6 mm), and also featured larger, 3.25 in (83 mm) main journals. Unlike previous enlargements of this engine, it did not replace the 389. The 421 SD became factory installed in 1962 and in 1963 a street version became available from the factory with a four barrel or tri-power carburation. The Super Duty versions of this engine were extensively used in NASCAR stock car racing and drag racing competition. The 421 also marked the end of the option for a forged steel crankshaft. The Armasteel cast crankshaft was the standard crankshaft of the entire Pontiac V-8 line until '67. While "Armasteel" was no more than a fancy name for a hardened cast iron unit, it did refer to the "locking ball" as opposed to the "flaking" type cast iron found in other engines. In '67, Pontiac out of concerns the public misunderstood the engineering terms, went to a Nodular cast iron name crankshaft, which they used until 1975. Jeff Burton (99), Elliott Sadler (38), Ricky Rudd (21), Dale Jarrett (88), Sterling Marlin (40), Jimmie Johnson (48), and Casey Mears (41) practice for the 2004 Daytona 500 The National Association for Stock Car Auto Racing (NASCAR) is the largest sanctioning body of motorsports in the United States. ... This article is about the sport of stock car racing. ... Top Fuel dragster Drag racing is a sport in which cars race down a track with a set distance as fast as possible. ...

428

In 1967 the 421 was bored to 4.12 in (104.7 mm), increasing its displacement to 428 in³ (7.0 L). The 428 had the same 4.00" stroke as the 421, and was produced from 1967 to 1969. The Crankshaft in the 428 also had a N cast on them as opposed to the 421's armasteel. In 1969, Pontiac also used a revised Crankshaft out of a Pearlitic Malleable Iron although it still used the" N" i.d. cast letter. This new material had stronger alloys in the iron. All 428 engines were factory install in large cars only. However, there were a few dealers that would install a 428 in a customers GTO or Firebird for higher power levels.

It was replaced by the 455 for the 1970 model year.

455

For 1970, the 428 bore was expanded to 4.152 inches, combined with a 4.21 inch stroke (105.5 mm by 106.9 mm), yielding a total displacement of 455 in³ (7.5 L). The engine became available for the first time in Pontiac Firebirds and the Pontiac GTO, as GM lifted its restrictions on the use of engines larger than 400 cubic inches (401 in some Buicks) in mid-sized cars. The Pontiac V8 design differs from other manufacturers' designs in that the external dimensions of each engine, from 326 - 455 in³ displacement, is identical. The displacement is determined internally with changes to the bore and stroke; therefore, there is no "big block" Pontiac engine. The 455 was used through 1976. The Pontiac Firebird was a pony car built by the Pontiac division of General Motors between 1967 and 2002. ... 1965 Pontiac GTO convertible The Pontiac GTO was an automobile built by Pontiac from 1964 to 1974, and by General Motors Holden in Australia from 2004 to 2006. ...

The 455, with its "undersquare" dimensions (long stroke relative to bore), emphasized torque over hp, and was somewhat less powerful than some high-performance iterations of the 400. For 1971 Pontiac introduced a High Output, H.O., version with standard internal parts, a 4-bolt main bearing cap equipped block, and improved cylinder head design with 1/8 inch taller intake ports and special round exhaust ports for better breathing, making some 335 hp (250 kW)/224 kW (310 hp in the more accurate SAE net system), but this was an extremely rare engine (it was standard in the Firebird Trans Am. In 1973, a further refined and even stronger version, the Super Duty (SD) engine was introduced with "only" 310 hp (231 kW)/231 kW (SAE net) using a similar camshaft specifications to the Ram Air Iv 400. The 455 SD used round port cylinder heads similar to those used on the 1971 and 1972 455 HO, with specific "LS2" intake and cast iron exhaust header-manifolds. Still, it was the strongest American engine offered that year. Its power was achieved through bending of EPA emissions-testing procedures, which led engineers to de-tune the engine to 290 hp (216 kW) via a camshaft change to the same profile used in the early RAIII 400 engines for mid 1973 and 1974, after which point it was discontinued. The Pontiac Firebird was a pony car built by the Pontiac division of General Motors between 1967 and 2002. ... EPA redirects here. ...

While an evolution of the RAIV and H.O. engine designs, the 455 SD was a much improved engine. In addition to the more refined cylinder heads, block casting reinforcements in the lifter galley and main bearing oil pan rail area along with the addition of forged connecting rods with larger 7/16 inch diameter bolts, the SD was made with a provision for dry sump oiling from the factory. This truly was a racing engine, detuned for use in passenger cars.

Ram Air

Ram Air

While not officially called the Ram Air I when it was issued, it was indeed the first in a series of Ram Air V8 engines from Pontiac. This engine was installed in the 1967 GTO/Firebird as the top of the line option and at 360 HP (underrated), it was the most advanced 400 in the line. This carried the 301/313 camshaft, as opposed to the "HO" cam which had less duration and overlap. It also had (along with the HO engine) the famous cast iron "headers" which were much better at reducing backflow than the regular manifolds.

Ram Air II

In 1968, Pontiac manufactured the the Ram Air II which was a 400 (360 HP) with the first production round port heads from the Pontiac Division. The first actual round ports were the Tunnel Port 428, which was a very radical racing engine not sold to the general public. The Ram Air II engine used the famous 301/313 camshaft...which was the same as the Ram Air III. This was the precursor to the Ram Air IV, which was issued the following year. Earlier in the mid 60's, Pontiac had experimented with round port heads...and tunnel port heads (which were based on the Ford 428 Tunnel Port. This led them to make the RA II in Mid 1968. This head, while impressive looking...was not a great improvement, flow wise, to the earlier "D" port heads. In fact, it's been said that both the 1963 Super Duty 421 head and the 1967 "670" casting flowed better. But is looked pretty!

Ram Air III

The Ram Air III is a 400 cubic inch engine with a wilder 301/313 duration camshaft than the garden variety 400 installed in most high performance Pontiacs.. This engine was installed in both GTO's and Firebirds. It really was a hybrid between the regular 400 "D" port, and the Ram Air IV. it was rated at 360 HP...but made much more with tuning... it also had the Ram Air IV's 4-bolt mains.

Ram Air IV

The Ram Air IV was a improvement of the Ram Air II. In it, the head flow was improved drastically, as well as the material of the valves and valve springs themselves. Until the 1973 Super Duty, these heads were the best flowing of any Pontiac engine, flowing even more than the 1963 Super Duty. This engine used the 308/320 camshaft which was so radical, it had trouble passing emissions standards.

The Ram Air IV found its way into GTO's and Firebirds, although was restricted to 335 hp by way of a throttle stop for the Firebird platform to meet the restriction of hp vs weight limitations from GM.

Ram Air V

(303, 366, 400, 428) In 1969 Pontiac created several versions of their "tunnel port" engine: a special short-deck version of the V8 for Trans Am racing and a 400 standard deck version. The factory also experimented with 366 and 428 in³ versions. The cylinder head was patterned after the highly successful Ford 427 tunnel port head. So large were the intake ports that the pushrods ran through the center of the ports via pressed-in tubes. The Trans-Am Series was created in 1966 by the SCCA as the Trans-American Sedan Championship. ...

303 - The revised engine had shorter connecting rods, smaller 2.5 in. (63.5 mm) journals, special "tunnel port" heads, and a solid-lifter version of the 400's Ram Air IV camshaft. It shared the 4.125 in (104.8 mm) bore of the 400, but with a 2.84 in (72.1 mm) stroke for a displacement of 303 in³ (5.0 L). The short-deck engine weighed about 40 lb (18 kg) less than the 400, and had an 8000 rpm redline. The 303 program was promising, with race-ready engines producing 475-525 hp (354.4-391.7 kW) and slated for advertised ratings of 355 hp (265 kW) in the Pontiac Firebird and 375 hp (280 kW) for the Pontiac GTO. Concerns about emissions, the response of the automobile safety lobby, and the warranty implications of a high-revving street engine led to its cancellation. SCCA Trans-Am series General Competition Rules required an engine to be a "Production" item, and required a production of no less than 250 units. The total number of Ram Air V 303 engines produced is not known, estimates range from the SCCA required 250 units, up to 500 units, with rumors of a handful of Ram Air V 303's making their way into the Pontiac Trans-Am production line. These engines are extremely rare and parts not readily available. The Pontiac Firebird was a pony car built by the Pontiac division of General Motors between 1967 and 2002. ... 1965 Pontiac GTO convertible The Pontiac GTO was an automobile built by Pontiac from 1964 to 1974, and by General Motors Holden in Australia from 2004 to 2006. ... In commercial and consumer transactions, a warranty is an obligation that an article or service sold is as factually stated or legally implied by the seller, and that often provides for a specific remedy such as repair or replacement in the event the article or service fails to meet the...

Ram Air VI

The 428 engines were known as the Ram Air VI.

Ram Air VII

The 428 engines were known as the Ram Air VI and Ram Air VII respectively, the difference between them being that the Ram Air VII was developed with twin four barrel carburetors.

The Super Dutys

SD389

SD421

SD455

Available only in the 1973 and 1974 Formula Firebird and Firebird Trans AM. The SD-455 consisted of a strengthened cylinder block that included 4 bolt main bearings and additional material in various locations for improved strength. Original plans called for a forged crankshaft, although actual production SD455s received nodular iron crankshafts with minor enhancements. Forged rods and forged aluminum pistons were specified, as were unique high flow cylinder heads. A camshaft with 301/313 degrees of advertised duration, 0.407 inch net valve lift, and 76 degrees of valve overlap was specified for actual production engines in lieu of the significantly more aggressive RAM AIR IV style cam that had originally been planned for the engine (initially rated at 310 HP with that cam), but ultimately proved incapable of meeting the tightening emissions standards of the era. The very modest cam, combined with a low compression ratio of 8.4 (advertised) and 7.9:1 actual resulted in 290 SAE NET HP. The initial press cars that were given to the various enthusiast magazines (e.g. HOT ROD and CAR AND DRIVER) were fitted with the RAM AIR IV style cam and functional hoodscoops - a fact that has been confirmed by several Pontiac sources. Actual production test cars ran considerably slower and yielded 1/4 miles times in the 14.5 second/98 MPH range in showroom tune - results that are quite consistent for a car with a curb weight of 3,850 pounds and the rated 290 SAE NET HP figure that some sources suggest was "under-rated." Various Pontiac sources have emphatically stated that NO 310 HP versions of the SD455 were installed in regular production cars. 1975 Factory Service Manual lists the SD455, but the SD455 did not meet emissions for the 1975 model year and was canceled.

SD4

While not a V8, the SD4 was the last in a line of high performance Pontiac engines. The SD4 was available in the Indy Fiero. Over the counter parts could garner a 2.7L 272 hp (203 kW) version and a 3.2L 330 hp (250 kW) version. See the Iron Duke 2.5L 4 cyl engine[1].

Pontiac HO engines

326 HO

350 HO

In 1968, There was also a 350 "HO" which had an increased horsepower with the addition of higher compression #18 heads, (#17 and #46 were the most common 2 barrel heads)a 4 barrel carb and matching intake that was also used on the 400 and 428 engines. There was also the addition of dual exhaust, and in the case of a stick shift car, a slightly more aggressive cam.

In 1969, the 350HO was upgraded again with the addition of the 400 HO cam, commonly referred to by Pontiac hobbyists as the 068 cam. Also the addition of #48 casting number heads with a 68 cc chamber for higher compression, along with larger 2.11" & 1.77" valves. Free flowing exhaust manifolds from the 400 RamAir was used late in the model year. This was under rated at 325 horsepower (242 kW). Many of cousin division more popular Chevolet 350's and even base SS396's were handily beaten by this little 350"High Output"(HO) Pontiac. This may be today one of the most over looked high performance engines of the era, as it was overlooked by the buyers of larger 400 engines available in the day.

400 HO

In 1978 the 400 HO was created to fulfill the vacuum of the lackluster 76 455 HO, with improved flow cyl "6X" casting heads borrowed from the 350 yielding higher compression, specific camshaft, 3.23 gearing, and a new dual muffler exhaust making 220 hp (160 kW), providing the Trans AM and Formula Firebird with a breath of new life after some dismal performance years. The 4 speed manual transmission was also available behind the 400 HO and the 301 HO. The 400 HO did not live long however, emission standards and fuel economy restrictions for 1980 model year doomed the powerplant. The 301 Turbo replaced the 400 HO in 1980, disappointing potential customers who were just getting excited about performance returning to Pontiac. The 400 HO Trans AM was the last of the performance cars available with the manual transmission, also yet another disappointment to potential customers.

No hood scoop moniker denoted the 220hp 400 HO except the standard "T/A 6.6". The 185 hp 403 Oldsmobile powered cars had "6.6L Litre". Historically the "T/A" prefix on the hoodscoop noted that it was a Pontiac sourced engine, and those ending in Litre were non Pontiac, with the exception of the 1976 50th Anniversary Pontiac Trans AM model.

455 HO

First 455 HO's were seen in the 1971 model year with HD blocks, special large valve heads with screw in rocker arm studs, special aluminum intake with removable exhaust crossover, special streamlined exhaust manifolds, higher lift and larger duration camshaft and 800 CFM Quadrajet carburetor with specific jetting.

The 455 HO's were similar to the yet to come SD455 in 1973/74. The 455 HO was available in the Firebird (base, Forumula and Trans AM), and the LeMans, GTO, T37 and GT37 models. The SD455 took the HO 455 to the next level in durabilty, power and performance.

Last seen in 1976, ending the era of the 455 HO in lackluster fashion, delivering only a paltry 200 hp (150 kW). It shared nothing with its 1971 brethern except the displacement. Standard in Catalina/ Bonneville Wagons. Option in LeMans, Grand LeMans, Firebird Trans Am, Catalina, Bonneville and Grand Prix.

Details of the 1971 455

Details of the 1972 455

Details of the 1973 455

Details of the 1974 455

Details of the 1975 455

Details of the 1976 455

301 HO

While not "high output" fashion by the 60's and 70's standards and no "HO" moniker on the shaker hood scoop, the 301 did end up with a HO "performance" version, yielding 170hp with only 4.9L CID for the 1979-1981 model years.

The 301 HO was the base Trans AM engine in 1980 and 1981.

Modifications over the std 301 4BBL were the 301 Turbo "301T" block, the ESC (Electronic Spark Control) distributor and controller borrowed from the 301 Turbo which allowed for higher timing without the penalty of engine damaging pinging or preignition, a large 4" ram air duct to the air cleaner, specific carb calibration for the 301 HO, and cam similar in grind to the 2200 hp 400 from the 1978-1979 model year. Unfortunately no improvements in casting "01" small valve high velocity heads, which could have yielded greater improvements in power.

Pontiac Experimental V8 Engines

427 Hemi SOHC

Features: Thin Wall, Cast Aluminum Block 4.257 Bore x 3.75" stroke (3.0" Mains) Forged Steel 6.625" rods (Ram Air V style) 12:1 compression Mechanical Port Fuel Injection

Large Valve Heads: 2.40" Intake Valve 2.00" Exhaust Valve

Small Valve High Rpm 2.19" Intake Valve 2.00" Exhaust Valve

Splayed Main Caps, head bolts tie into main caps. Head bolts do not pull on the cylinder wall causing distortion. Cam Drive: Fiberglass Belt Max RPM (High RPM Engine): >8000 rpm Engine Weight: Estimated 550 lb (249 kg) complete

Dimensions: Width: 32" Length: 32" Height: 24.6"

Power: estimated 640 hp (480 kW) @ 7500 rpm

421 2 Valve SOHC

3 Valve SOHC

389 4 Valve DOHC

Aluminum right 400

Pontiac Four-Cylinder

195

Perhaps the most unusual variation of the durable Pontiac V8 was not a V8 at all, but an inline four. Created for the 1961 Pontiac Tempest, it was essentially the right bank of the 389, sharing most of its tooling and many of its parts (more than 120 were identical). The bore and stroke of 4.06 in (103.2 mm) and 3.75 in (95.3 mm) were the same, giving a displacement of 194.4 in³ (3.2 L). This degree of commonality enabled it to be produced on the same lines as the V8, allowing substantial cost savings. A drawback was that the 195 weighed much more than a purpose-designed engine: at about 540 lb (245 kg), it was not substantially lighter than the 389. The straight-4 or inline-4 is an internal combustion engine with four cylinders aligned in one row. ... The Pontiac Tempest was an entry-level compact automobile produced by the Pontiac Motor Division of General Motors, introduced in September 1960 for the 1961 model year. ...

The 195 produced 110 hp (82 kW) (gross) at 3800 rpm and 190 ft·lbf (258 N·m) at 2000 rpm with a single-barrel carburetor, or 155 hp (116 kW) @ 4800 and 215 ft·lbf (292 N·m) @ 2800 rpm with the optional four-barrel carburetor. For 1962 a "power pack" option increased rated power to 166 hp (124 kW).

The Achilles heel of the 195 was engine shake. An inline four-cylinder engine produces unbalanced "couple," shaking in the vertical plane, and modern engineers consider the installation of twin counter-rotating balance shafts necessary for engines much larger than 122 in³ (2.0 L). The V8-based design of the 195 had no such balance shafts, and costs prohibited adding them. The 195 was instead cushioned by flexible rubber engine mounts designed to isolate the engine from the rest of the car, and its forces were further dampened by the Tempest's unusual driveshaft, but if the engine was out of tune or if a spark plug became fouled, the shaking grew worse than the mounts could hide. A special high-strength timing chain was developed especially for the Tempest 4, since a standard chain would stretch and break rather easily from the inherent vibration in this engine design. The timing chain in the 195 was the same as the 389 initially, the upgraded Tempest chain also works on the V8 engines as a high strength upgrade. As an aside, former Pontiac engineer Malcolm McKellar joked in an interview with Collectible Automobile magazine that he and his fellow engineers sometimes called the four-cylinder Tempest "a traveling fatigue machine." In Greek mythology, Achilles is made invulnerable by being dipped in the river Styx by his mother, Thetis. ... The straight-4 or inline-4 is an internal combustion engine with four cylinders aligned in one row. ... Balance shaft in Ford Taunus V4 engine. ... This article is about the mechanical device. ... This article or section should include material from Spark gap A spark plug is an electrical device that fits into the cylinder head of some internal combustion engines and ignites compressed aerosol gasoline by means of an electric spark. ...

The 195 was dropped after 1963, although Porsche would use a "half-a-V8" inline-four (with a rear-mounted transmission) for its later Porsche 944 model. This article is about the auto company. ... The 944 was a sports car built by Porsche from 1982 to 1991. ...

See also

• Pontiac Straight-6 engine
• Pontiac Straight-8 engine
• List of GM engines