Carbon nanotubes have many potential applications, here is a short list of some of the most important:

Structural

• clothes: waterproof tear-resistant cloth fibers
• combat jackets: MIT is working on combat jackets that use carbon nanotubes as ultrastrong fibers and to monitor the condition of the wearer. [1]
• concrete: In concrete, they increase the tensile strength, and halt crack propagation.
• polyethylene: Researchers have found that adding them to polyethylene increases the polymer's elastic modulus by 30%.
• sports equipment: Stronger and lighter tennis rackets, bike parts, golf balls, golf clubs, golf shaft and baseball bats.
• space elevator: This will be possible only if tensile strengths of more than about 70 GPa can be achieved. Monoatomic oxygen in the Earth's upper atmosphere would erode carbon nanotubes at some altitudes, so a space elevator constructed of nanotubes would need to be protected (by some kind of coating). Carbon nanotubes in other applications would generally not need such surface protection.
• ultrahigh-speed flywheels: The high strength/weight ratio enables very high speeds to be achieved.
• Bridges: For instance in suspension bridges (where they will be able to replace steel), or bridges built as a "horizontal space elevator".

Mapúa Institute of Technology (MIT, MapúaTech or simply Mapúa) is a private, non-sectarian, Filipino tertiary institute located in Intramuros, Manila. ... ... The most common form of concrete consists of Portland cement, construction aggregate (generally gravel and sand) and water. ... Polyethylene or polyethene is a thermoplastic commodity heavily used in consumer products (over 60M tons are produced worldwide every year). ... ... A space elevator would consist of a cable attached to Earths surface, reaching into space. ... General Name, Symbol, Number oxygen, O, 8 Chemical series Nonmetals, chalcogens Group, Period, Block 16, 2, p Appearance colorless (gas) very pale blue (liquid) Atomic mass 15. ... A space elevator would consist of a cable attached to Earths surface, reaching into space. ... Spoked flywheel Simple flywheel in motion. ...

Electromagnetic

• artificial muscles^[1]
• buckypaper - a thin sheet made from nanotubes that are 250 times stronger than steel and 10 times lighter that could be used as a heat sink for chipboards, a backlight for LCD screens or as a faraday cage to protect electrical devices/aeroplanes.
• chemical nanowires: Carbon nanotubes additionally can also be used to produce nanowires of other chemicals, such as gold or zinc oxide. These nanowires in turn can be used to cast nanotubes of other chemicals, such as gallium nitride. These can have very different properties from CNTs - for example, gallium nitride nanotubes are hydrophilic, while CNTs are hydrophobic, giving them possible uses in organic chemistry that CNTs could not be used for.
• computer circuits: A nanotube formed by joining nanotubes of two different diameters end to end can act as a diode, suggesting the possibility of constructing electronic computer circuits entirely out of nanotubes. Because of their good thermal properties, CNTs can also be used to dissipate heat from tiny computer chips. The longest electricity conducting circuit is a fraction of an inch long.(Source: June 2006 National Geographic).
• conductive films: A 2005 paper in Science notes that drawing transparent high strength swathes of SWNT is a functional production technique (Zhang et. al., vol. 309, p. 1215). Additionally, Eikos Inc.^[2] of Franklin, Massachusetts is developing transparent, electrically conductive films of carbon nanotubes to replace indium tin oxide (ITO) in LCDs, touch screens, and photovoltaic devices. Carbon nanotube films are substantially more mechanically robust than ITO films, making them ideal for high reliability touch screens and flexible displays. Nanotube films show promise for use in displays for computers, cell phones, PDAs, and ATMs.
• electric motor brushes: Conductive carbon nanotubes have been used for several years in brushes for commercial electric motors. They replace traditional carbon black, which is mostly impure spherical carbon fullerenes. The nanotubes improve electrical and thermal conductivity because they stretch through the plastic matrix of the brush. This permits the carbon filler to be reduced from 30% down to 3.6%, so that more matrix is present in the brush. Nanotube composite motor brushes are better-lubricated (from the matrix), cooler-running (both from better lubrication and superior thermal conductivity), less brittle (more matrix, and fiber reinforcement), stronger and more accurately moldable (more matrix). Since brushes are a critical failure point in electric motors, and also don't need much material, they became economical before almost any other application.
• light bulb filament: alternative to tungsten filaments in incandescent lamps.
• magnets: MWNTs coated with magnetite
• optical ignition: A layer of 29% iron enriched SWNT is placed on top of a layer of explosive material such as PETN, and can be ignited with a regular camera flash.
• solar cells: GE's carbon nanotube diode has a photovoltaic effect. Nanotubes can replace ITO in some solar cells to act as a transparent conductive film in solar cells to allow light to pass to the active layers and generate photocurrent.
• superconductor: Nanotubes have been shown to be superconducting at low temperatures.
• ultracapacitors: MIT is researching the use of nanotubes bound to the charge plates of capacitors in order to dramatically increase the surface area and therefore energy storage ability.^[3]
• displays: One use for nanotubes that has already been developed is as extremely fine electron guns, which could be used as miniature cathode ray tubes in thin high-brightness low-energy low-weight displays. This type of display would consist of a group of many tiny CRTs, each providing the electrons to hit the phosphor of one pixel, instead of having one giant CRT whose electrons are aimed using electric and magnetic fields. These displays are known as field emission displays (FEDs).
• transistor: developed at Delft, IBM, and NEC.

It has been suggested that Bucky gel actuator be merged into this article or section. ... Buckypaper is a thin sheet made from carbon nanotubes that is 250 times stronger than steel and 10 times lighter. ... This article or section does not cite its references or sources. ... LCD redirects here. ... Entrance to a Faraday room In electromagnetism, the Faraday cage is an application of Gausss law, one of Maxwells equations. ... Hydrophile, from the Greek (hydros) water and φιλια (philia) friendship, refers to a physical property of a molecule that can transiently bond with water (H2O) through hydrogen bonding. ... Hydrophobe (from the Greek (hydros) water and (phobos) fear) in chemistry refers to the physical property of a molecule that is repelled by water. ... Types of diodes In electronics, a diode is a component that restricts the direction of movement of charge carriers. ... Science is the journal of the American Association for the Advancement of Science (AAAS). ... Indium tin oxide (ITO) is a mixture of indium(III) oxide (In2O3) and tin(IV) oxide (SnO2), typically 90% In2O3, 10% SnO2 by weight. ... To meet Wikipedias quality standards, this article or section can be improved by converting lengthy lists to text. ... An NCR interior, multi-function ATM in the USA Smaller indoor ATMs dispense money inside convenience stores and other busy areas, such as this off-premise Wincor Nixdorf mono-function ATM in Sweden An on-premise NCR interior, multi-function through-the-wall ATM at a CIBC branch in Canada... Carbon black is a material produced by the incomplete combustion of petroleum products. ... The incandescent light bulb (archaically known as the electric lamp) uses a glowing wire filament heated to white-hot by electrical resistance, to generate light (a process known as thermal radiation or incandescence). ... Mwnt is a very small community in south Ceredigion, Wales. ... // Headline text Magnetite is a ferrimagnetic mineral form of iron(II,III) oxide, with chemical formula Fe3O4, one of several iron oxides and a member of the spinel group. ... An electronic device known as a diode can be formed by joining two nanoscale carbon tubes with different electronic properties. ... PETN (Pentaerythritol Tetranitrate, also known as Penthrite) is one of the strongest known high explosives, with a relative effectiveness factor (R.E. factor) of 1. ... A solar cell, a form of photovoltaic cell, is a device that uses the photoelectric effect to generate electricity from light, thus generating solar power (energy). ... Superconductivity is a phenomenon occurring in certain materials at low temperatures, characterised by the complete absence of electrical resistance and the damping of the interior magnetic field (the Meissner effect. ... A magnet levitating above a high-temperature superconductor (with boiling liquid nitrogen underneath), demonstrating the Meissner effect. ... An Ultracapacitor is a capacitor that has an unusually large amount of energy storage capability relative to its size when compared to common capacitors. ... Only meanings of encyclopedic scope are listed here for disambiguation purposes. ... Cathode ray tube employing electromagnetic focus and deflection Cutaway rendering of a color CRT Electron guns Electron beams Focusing coils Deflection coils Anode connection Mask for separating beams for red, green, and blue part of displayed image Phosphor layer with red, green, and blue zones Close-up of the phosphor... Properties The electron is a lightweight fundamental subatomic particle that carries a negative electric charge. ... A phosphor is a substance that can exhibit the phenomenon of fluorescence (glowing during absorption of radiation of another kind) or phosphorescence (sustained glowing without further stimulus). ... This example shows an image with a portion greatly enlarged, in which the individual pixels are rendered as little squares and can easily be seen. ... Current (I) flowing through a wire produces a magnetic field (B) around the wire. ... A field emission display (FED) is a type of flat panel display using phosphor coatings as the emissive medium. ... Assorted transistors The transistor is a solid state semiconductor device that can be used for amplification, switching, voltage stabilization, signal modulation and many other functions. ...

Chemical

• air pollution filter: Future applications of nanotube membranes include filtering carbon dioxide from power plant emissions.^[4]
• biotech container: Nanotubes can be opened and filled with materials such as biological molecules, raising the possibility of applications in biotechnology.
• water filter: Recently nanotube membranes have been developed for use in filtration. This technique can purportedly reduce desalination costs by 75%. The tubes are so thin that small particles (like water molecules) can pass through them, while larger particles (such as the chloride ions in salt) are blocked.

The structure of insulin Biotechnology is a technology based on biology, especially when used in agriculture, food science, and medicine. ...

Mechanical

• oscillator: fastest known oscillators (> 50 GHz).
• liquid flow array: Liquid flows up to five orders of magnitude faster than predicted through array.
• slick surface: slicker than Teflon and waterproof.

In electrical circuits

Carbon nanotubes have many properties—from their unique dimensions to an unusual current conduction mechanism—that make them ideal components of electrical circuits. Currently, there is no reliable way to arrange carbon nanotubes into a circuit. Electrical conduction is the movement of electrically charged particles through matter. ...

The major hurdles that must be jumped for carbon nanotubes to find prominent places in circuits relate to fabrication difficulties. The production of electrical circuits with carbon nanotubes are very different from the traditional IC fabrication process. The IC fabrication process is somewhat like sculpture - films are deposited onto a wafer and pattern-etched away. Because carbon nanotubes are fundamentally different from films, carbon nanotube circuits can so far not be mass produced. Nasas Glenn Research Center clean room. ... An Italian Futurist sculpture by Umberto Boccioni at the Museum of Modern Art in New York City (MoMA). ...

Researchers sometimes resort to manipulating nanotubes one-by-one with the tip of an atomic force microscope in a painstaking, time-consuming process. Perhaps the best hope is that carbon nanotubes can be grown through a chemical vapor deposition process from patterned catalyst material on a wafer, which serve as growth sites and allow designers to position one end of the nanotube. During the deposition process, an electric field can be applied to direct the growth of the nanotubes, which tend to grow along the field lines from negative to positive polarity. Another way for the self assembly of the carbon nanotube transistors consist in using chemical or biological techniques to place the nanotubes from solution to determinate place on a substrate. // AFM The atomic force microscope (AFM) is a very high-resolution type of scanning probe microscope. ... DC plasma (violet) enhances the growth of carbon nanotubes in this laboratory-scale PECVD apparatus. ... In chemistry, a catalyst (Greek: καταλύτης, catalytēs) is a substance that decreases the activation energy of a chemical reaction (see also catalysis) without itself being changed at the end of the chemical reaction. ... In physics, an electric field or E-field is an effect produced by an electric charge (or a time-varying magnetic field) that exerts a force on charged objects in the field. ...

Even if nanotubes could be precisely positioned, there remains the problem that, to this date, engineers have been unable to control the types of nanotubes—metallic, semiconducting, single-walled, multi-walled—produced. A chemical engineering solution is needed if nanotubes are to become feasible for commercial circuits. ur mom Chemical engineering is the branch of engineering that deals with the application of physical science (in particular chemistry and physics) and mathematics to the process of converting raw materials or chemicals into more useful or valuable forms. ...

As fiber and film

One application for nanotubes that is currently being researched is high tensile strength fibers. Two methods are currently being tested for the manufacture of such fibers. A French team has developed a liquid spun system that involves pulling a fiber of nanotubes from a bath which yields a product that is approximately 60% nanotubes^{[citation needed]}. The other method, which is simpler but produces weaker fibers uses traditional melt-drawn polymer fiber techniques with nanotubes mixed in the polymer. After drawing, the fibers can have the polymer component burned out of them leaving only the nanotube or they can be left as they are. It has been suggested that this article or section be merged into Strength of materials. ... Fiber or fibre[1] is a class of materials that are continuous filaments or are in discrete elongated pieces, similar to lengths of thread. ... Polymer is a term used to describe molecules consisting of structural units and a large number of repeating units connected by covalent chemical bonds. ...

Ray Baughman's group from the NanoTech Institute at University of Texas at Dallas produced the current toughest material known as of mid-2003 by spinning fibers of single wall carbon nanotubes with polyvinyl alcohol. Beating the previous contender, spider silk, by a factor of four, the fibers require 600 J/g to break^[5] In comparison, the bullet-resistant fiber Kevlar is 27–33 J/g. In mid-2005, Baughman and co-workers from Australia's Commonwealth Scientific and Industrial Research Organization developed a method for producing transparent carbon nanotube sheets 1/1000th the thickness of a human hair capable of supporting 50,000 times their own mass. In August 2005, Ray Baughman's team managed to develop a fast method to manufacture up to seven meters per minute of nanotube tape.^[6] Once washed with ethanol, the ribbon is only 50 nanometers thick; a square kilometer of the material would only weigh 30 kilograms. The University of Texas at Dallas is a branch of the UT system, which, despite its name, is located in the Dallas suburb of Richardson, Texas. ... 2003 (MMIII) was a common year starting on Wednesday of the Gregorian calendar. ... This article needs to be wikified. ... Spider silk is a fibre secreted by spiders. ... In materials science and metallurgy, toughness is the resistance to fracture of a material when stressed. ... Kevlar is DuPont Companys brand name for a particular light but very strong aramid fibre. ... 2005 (MMV) was a common year starting on Saturday of the Gregorian calendar. ... The Commonwealth Scientific and Industrial Research Organisation (CSIRO) is the national government body for scientific research in Australia. ... Ethanol, also known as ethyl alcohol or grain alcohol, is a flammable, colorless, mildly toxic chemical compound with a distinctive perfume-like odor, and is the alcohol found in alcoholic beverages. ... A nanometre (American spelling: nanometer) is 1. ...

In 2004, Alan Windle's group of scientists at the Cambridge-MIT Institute developed a way to make carbon nanotube fiber continuously at the speed of several centimetres per second just as nanotubes are produced. One thread of carbon nanotubes was more than 100 metres long. The resulting fibers are electrically conductive and as strong as ordinary textile threads.^[7][8] 2004 (MMIV) was a leap year starting on Thursday of the Gregorian calendar. ... The Cambridge-MIT Institute, or CMI, is a partnership between the University of Cambridge in Cambridge, UK, and the Massachusetts Institute of Technology in Cambridge, Massachusetts. ...

References