Resistor		Variable Resistor

Resistor symbols (American)

Resistor		Variable resistor

Resistor symbols (Europe, IEC)

Axial-lead resistors on tape. The tape is removed during assembly before the leads are formed and the part is inserted into the board.

Three carbon composition resistors in a 1960s valve radio.

A resistor is a two-terminal electrical or electronic component that resists an electric current by producing a voltage drop between its terminals in accordance with Ohm's law: The electrical resistance is equal to the voltage drop across the resistor divided by the current through the resistor. Resistors are used as part of electrical networks and electronic circuits. Image File history File links Potentiometer_symbol. ... Image File history File links This is a lossless scalable vector image. ... Image File history File links This is a lossless scalable vector image. ... Image File history File links Potentiometer_symbol_Europe. ... Image File history File links Resistor_symbol_Europe. ... Image File history File links Variable_resistor_symbol_Europe. ... The International Electrotechnical Commission (IEC) is an international standards organization dealing with electrical, electronic and related technologies. ... Picture of some resistors I have. ... Picture of some resistors I have. ... Image File history File links Metadata Size of this preview: 800 × 476 pixelsFull resolution‎ (1,275 × 759 pixels, file size: 188 KB, MIME type: image/jpeg) Some old carbon? resistors in and old valve radio. ... Image File history File links Metadata Size of this preview: 800 × 476 pixelsFull resolution‎ (1,275 × 759 pixels, file size: 188 KB, MIME type: image/jpeg) Some old carbon? resistors in and old valve radio. ... Electricity (from New Latin ēlectricus, amberlike) is a general term for a variety of phenomena resulting from the presence and flow of electric charge. ... This article is about the engineering discipline. ... Electric current is the flow (movement) of electric charge. ... A voltage source, V, drives an electric current, I , through resistor, R, the three quantities obeying Ohms law: V = IR Ohms law states that, in an electrical circuit, the current passing through a conductor between two points is proportional to the potential difference (i. ... Electrical resistance is a measure of the degree to which an electrical component opposes the passage of current. ... International safety symbol Caution, risk of electric shock (ISO 3864), colloquially known as high voltage symbol. ... An electrical network or electrical circuit is an interconnection of analog electrical elements such as resistors, inductors, capacitors, diodes, switches and transistors. ...

Identifying resistors

Most axial resistors use a pattern of colored stripes to indicate resistance. Surface-mount ones are marked numerically. Cases are usually brown, blue, or green, though other colors are occasionally found such as dark red or dark grey. Surface-mount components on a keydrives circuit board Surface mount technology (SMT) is a method for constructing electronic circuits in which the components are mounted directly onto the surface of printed circuit boards (PCBs). ...

One can also use a multimeter or ohmmeter to test the values of a resistor. A digital multimeter A low cost digital multimeter An analog benchtop multimeter A multimeter or a multitester is an electronic measuring instrument that combines several functions in one unit. ... An Ohmmeter is an electrical measuring instrument that measures electrical resistance, the opposition to the flow of an electric current. ...

Four-band axial resistors

Main article: Electronic color code

Four-band identification is the most commonly used color coding scheme on all resistors. It consists of four colored bands that are painted around the body of the resistor. The scheme is simple: The first two numbers are the first two significant digits of the resistance value, the third is a multiplier, and the fourth is the tolerance of the value. Each color corresponds to a certain number, shown in the chart below. The tolerance for a 4-band resistor will be 1%, 5%, or 10%. The electronic color code discussed here is used to indicate the values or ratings of electronic components, very commonly for resistors, but also for capacitors, inductors, and others. ...

Preferred values

Main article: Preferred number

Resistors are manufactured in values from a few milliohms to about a gigaohm; only a limited range of values from the IEC 60063 preferred number series are commonly available. These series are called E6, E12, E24, E96 and E192. The number tells how many standardized values exist in each decade (e.g. between 10 and 100, or between 100 and 1000). So resistors conforming to the E12 series, can have 12 distinct values between 10 and 100, whereas those confirming to the E24 series would have 24 distinct values. In practice, the discrete component sold as a "resistor" is not a perfect resistance, as defined above. Resistors are often marked with their tolerance (maximum expected variation from the marked resistance). In industrial design, product developers must choose numerous lengths, distances, diameters, volumes, and other characteristic quantities. ... The International Electrotechnical Commission (IEC) is an international standards organization dealing with electrical, electronic and related technologies. ... In industrial design, product developers must choose numerous lengths, distances, diameters, volumes, and other characteristic quantities. ... Tolerance in Final Fantasy is an allowance, given as a permissible range, in the nominal dimension or value specification of a manufactured object. ...

5-band axial resistors

5-band identification is used for higher precision (lower tolerance) resistors (1%, 0.5%, 0.25%, 0.1%), to notate the extra digit. The first three bands represent the significant digits, the fourth is the multiplier, and the fifth is the tolerance. 5-band standard tolerance resistors are sometimes encountered, generally on older or specialized resistors. They can be identified by noting a standard tolerance color in the 4th band. The 5th band in this case is the temperature coefficient “Accuracy” redirects here. ... Tolerance in Final Fantasy is an allowance, given as a permissible range, in the nominal dimension or value specification of a manufactured object. ... Tolerance in Final Fantasy is an allowance, given as a permissible range, in the nominal dimension or value specification of a manufactured object. ...

SMT resistors

This image shows four surface mount resistors (the component at the upper left is a capacitor) including two zero-ohm resistors. Zero-ohm links are often used instead of wire links, so that they can be inserted by a resistor-inserting machine.

Surface mounted resistors are printed with numerical values in a code related to that used on axial resistors. Standard-tolerance Surface Mount Technology (SMT) resistors are marked with a three-digit code, in which the first two digits are the first two significant digits of the value and the third digit is the power of ten (the number of zeroes). For example: Image File history File linksMetadata Zero_ohm_resistors_cropped. ... Image File history File linksMetadata Zero_ohm_resistors_cropped. ... A zero-ohm link or zero-ohm resistor is a wire link used to connect traces on a printed circuit board that is packaged in the same format as a resistor, to enable them to be placed on the cirrcuit board using same automated equipment used to place resistors. ... Surface-mount components on a flash drives circuit board Surface mount technology (SMT) is a method for constructing electronic circuits in which the components (SMC, or Surface Mounted Components) are mounted directly onto the surface of printed circuit boards (PCBs). ... Surface-mount components on a flash drives circuit board Surface mount technology (SMT) is a method for constructing electronic circuits in which the components (SMC, or Surface Mounted Components) are mounted directly onto the surface of printed circuit boards (PCBs). ... Significant figures (also called significant digits and abbreviated sig figs or sig digs, respectively) is a method of expressing errors in measurements. ...

Resistances less than 100 ohms are written: 100, 220, 470. The final zero represents ten to the power zero, which is 1. For example:

Sometimes these values are marked as "10" or "22" to prevent a mistake.

Resistances less than 10 ohms have 'R' to indicate the position of the decimal point (radix point). For example: In mathematics, radix point refers to the symbol used in numerical representations to separate the integral part of the number (to the left of the radix) from its fractional part (to the right of the radix). ...

Precision resistors are marked with a four-digit code, in which the first three digits are the significant figures and the fourth is the power of ten. For example:

"000" and "0000" sometimes appear as values on surface-mount zero-ohm links, since these have (approximately) zero resistance. A zero-ohm link or zero-ohm resistor is a wire link used to connect traces on a printed circuit board that is packaged in the same format as a resistor, to enable them to be placed on the cirrcuit board using same automated equipment used to place resistors. ...

Industrial type designation

Format: [two letters]<space>[resistance value (three digit)]<nospace>[tolerance code(numerical - one digit)]

The operational temperature range distinguishes commercial grade, industrial grade and military grade components. For other uses, see Temperature (disambiguation). ... This article does not cite any references or sources. ...

• Commercial grade: 0 °C to 70 °C
• Industrial grade: −40 °C to 85 °C (sometimes −25 °C to 85 °C)
• Military grade: −55 °C to 125 °C (sometimes -65 °C to 275 °C)
• Standard Grade -5°C to 60°C

Resistor standards

• MIL-R-11
• MIL-R-39008
• MIL-R-39017
• MIL-PRF-26
• MIL-PRF-39007
• BS 1852
• EIA-RS-279

There are other MIL-R- standards.

Calculations

Ohm's law

The relationship between voltage, current, and resistance through a metal wire, and some other materials, is given by a simple equation called Ohm's Law: Ohms law, named after its discoverer Georg Ohm [1], states that the potential difference (or voltage drop V) between the ends of a conductor (for example, a resistor R) and the current, (I) flowing through R are proportional at a given temperature: where V is the voltage and I...

where V (or U in some languages) is the voltage (or potential difference) across the wire in volts, I is the current through the wire in amperes, and R, in ohms, is a constant called the resistance. (In fact this is only a simplification of the original Ohm's law—see the article on that law for further details.) Materials that obey this law over a certain voltage or current range are said to be ohmic over that range. An ideal resistor obeys the law across all frequencies and amplitudes of voltage or current. Josephson junction array chip developed by NIST as a standard volt. ... For other uses, see Ampere (disambiguation). ... The ohm (symbol: Ω) is the SI unit of electric resistance. ... A voltage source, V, drives an electric current, I , through resistor, R, the three quantities obeying Ohms law: V = IR Ohms law states that, in an electrical circuit, the current passing through a conductor between two points is proportional to the potential difference (i. ...

Superconducting materials at very low temperatures have zero resistance. Insulators (such as air, diamond, or other non-conducting materials) may have extremely high (but not infinite) resistance, but break down and admit a larger flow of current under sufficiently high voltage. A magnet levitating above a high-temperature superconductor, cooled with liquid nitrogen. ... Air redirects here. ... This article is about the mineral. ...

Resistance

The resistance of a resistor is given by the formula
where:

• ρ is the resistivity of the material that the resistor is made from
• l is the length of the resistive material, between the end contacts
• A is the (presumed uniform) cross sectional area of the resistive material

Electrical resistivity (also known as specific electrical resistance) is a measure of how strongly a material opposes the flow of electric current. ...

Power dissipation

The power dissipated by a resistor is the voltage across the resistor multiplied by the current through the resistor:

All three equations are equivalent. The first is derived from Joule's law, and other two are derived from that by Ohm's Law. Joules law (also known as Joule effect) is a physical law expressing the relationship between the heat generated by the current flowing through a conductor. ...

The total amount of heat energy released is the integral of the power over time:

If the average power dissipated exceeds the power rating of the resistor, then the resistor will first depart from its nominal resistance, and will then be destroyed by overheating.

Series and parallel circuits

Main article: Series and parallel circuits

Resistors in a parallel configuration each have the same potential difference (voltage). To find their total equivalent resistance (R_eq): Electrical circuit components can be connected together in one of two ways: series or parallel. ... Electrical circuit components can be connected together in one of two ways: series or parallel. ...

The parallel property can be represented in equations by two vertical lines "||" (as in geometry) to simplify equations. For two resistors, Image File history File links This is a lossless scalable vector image. ...

The current through resistors in series stays the same, but the voltage across each resistor can be different. The sum of the potential differences (voltage) is equal to the total voltage. To find their total resistance: Electrical circuit components can be connected together in one of two ways: series or parallel. ...

A resistor network that is a combination of parallel and series can sometimes be broken up into smaller parts that are either one or the other. For instance, Image File history File links This is a lossless scalable vector image. ...

However, many resistor networks cannot be split up in this way. Consider a cube, each edge of which has been replaced by a resistor. For example, determining the resistance between two opposite vertices requires matrix methods for the general case. However, if all twelve resistors are equal, the corner-to-corner resistance is ⁵⁄₆ of any one of them. Image File history File links This is a lossless scalable vector image. ... A cube[1] is a three-dimensional solid object bounded by six square faces, facets or sides, with three meeting at each vertex. ...

Technology

Carbon composition

Carbon composition resistors consist of a solid cylindrical resistive element with embedded wire leadouts or metal end caps to which the leadout wires are attached, which is protected with paint or plastic. A spiral is used to increase the length and decrease the width of the film, which increases the resistance.

The resistive element is made from a mixture of finely ground (powdered) carbon and an insulating material (usually ceramic). The mixture is held together by a resin. The resistance is determined by the ratio of the fill material (the powdered ceramic) and the carbon. Higher concentrations of carbon, a weak conductor, result in lower resistance. Carbon composition resistors were commonly used in the 1960s and earlier, but are not so popular for general use now as other types have better specifications, such as tolerance, voltage dependence, and stress (carbon composition resistors will change value when stressed with over-voltages).

Thick and thin film

Thick film resistors became popular during the 1970s, and most SMD resistors today are of this type. The principal difference between "thin film" and "thick film resistors" isn't necessarily the "thickness" of the film, but rather, how the film is applied to the cylinder (axial resistors) or the surface (SMD resistors). In thick film resistors the "film" is applied using traditional screen-printing technology.

Thin film resistors are made by sputtering the resistive material onto the surface of the resistor. Sputtering is sometimes called vacuum deposition. The thin film is then etched in a similar manner to the old (subtractive) process for making printed circuit boards: ie the surface is coated with a photo-sensitive material, then covered by a film, irradiated with ultraviolet light, and then the exposed photo-sensitive coating, and underlying thin film, are etched away. Sputtering is a physical vapor deposition, PVD process whereby atoms in a solid target material are ejected into the gas phase due to bombardment of the material by energetic ions. ... Vacuum deposition is a process used to create a thin layer of a substance (a coating) on a solid object (the substrate). ... It has been suggested that this article or section be merged with resist. ... For other uses, see Ultraviolet (disambiguation). ...

Thin film resistors, like their thick film counterparts, are then usually trimmed to an accurate value by abrasive or laser trimming. Laser trimming is a term that describes the manufacturing process of using a LASER to adjust the operating parameters of an electronic circuit. ...

Because the time during which the sputtering is performed can be controlled, the thickness of the film of a thin-film resistor can be accurately controlled. The type of the material is also usually different consisting of one or more ceramic (cermet) conductors such as tantalum nitride (TaN), ruthenium dioxide (RuO₂), lead oxide (PbO), bismuth ruthenate (Bi₂Ru₂O₇), nickel chromium (NiCr), and/or bismuth iridate (Bi₂Ir₂O₇). A Cermet is a composite material composed of ceramic (cer) and metallic (met) materials. ... Lead(II) oxide or litharge is a yellow oxide of lead of formula PbO, created by heating lead in air. ... Chromel is an alloy made of approximately 90 percent nickel and 10 percent chromium that is used to make the positive conductors of ANSI Type E and K thermocouples. ...

By contrast, thick film resistors, may use the same conductive ceramics, but they are mixed with sintered (powdered) glass, and some kind of liquid so that the composite can be screen-printed. This composite of glass and conductive ceramic (cermet) material is then fused (baked) in an oven at about 850 °C. Sintering is a method for making objects from powder, increasing the adhesion between particles as they are heated. ... Screen-printing, also known as silkscreening or serigraphy, is a printmaking technique that creates a sharp-edged single-color image using a stencil and a porous fabric. ...

Traditionally thick film resistors had tolerances of 5%, but in the last few decades, standard tolerances have improved to 2% and 1%. But beware, temperature coefficients of thick film resistors are tyically ±200 ppm, or ±250 ppm, depending on the resistance. Thus a 40 degree Celsius (70 °F) temperature change can add another 1% variation to a 1% resistor.

Thin film resistors are usually specified with tolerances of 0.1, 0.2, 0.5, and 1%, and with temperature coefficients of 5 to 25 ppm. They are usually far more expensive than their thick film cousins. Note, though, that SMD thin film resistors, with 0.5% tolerances, and with 25 ppm temperature coefficients, when bought in full size reel quantities, are about twice the cost of a 1%, 250 ppm thick film resistors.

Metal film

A common type of axial resistor today is referred to as a metal-film resistor. MELF (Metal Electrode Leadless Face) resistors often use the same technology, but are a cylindrically shaped resistor designed for surface mounting. [Note that other types of resistors, eg carbon composition, are also available in "MELF" packages].

Metal film resistors are usually coated with nickel chromium (NiCr), but might be coated with any of the cermet materials listed above for thin film resistors. Unlike thin film resistors, the material may be applied using different techniques than sputtering (though that is one such technique). Also, unlike thin-film resistors, the resistance value is determined by cutting a helix through the coating rather than by etching. [This is similar to the way carbon resistors are made.] The result is a reasonable tolerance (0.5, 1, or 2%) and a temperature coefficient of (usually) 25 or 50 ppm.

Wirewound

Wirewound resistors are commonly made by winding a metal wire around a ceramic, plastic, or fiberglass core. The ends of the wire are soldered or welded to two caps, attached to the ends of the core. The assembly is protected with a layer of paint, molded plastic, or an enamel coating baked at high temperature. The wire leads are usually between 0.6 and 0.8 mm in diameter and tinned for ease of soldering. For higher power wirewound resistors, either a ceramic outer case or an aluminium outer case on top of an insulating layer is used. The aluminium cased types are designed to be attached to a heatsink to dissipate the heat; the rated power is dependant on being used with a suitable heatsink, e.g., a 50 W power rated resistor will overheat at around one fifth of the power dissipation if not used with a heatsink. In a discussion of art technology, enamel (or vitreous enamel, or porcelain enamel in American English) is the colorful result of fusion of powdered glass to a substrate through the process of firing, usually between 750 and 850 degrees Celsius. ...

Because wirewound resistors are coils they have more inductance than other types of resistor, although this property can be minimized by winding the wire in sections with alternately reversed direction. For magnetic induction, see Magnetic field. ...

Foil resistor

Foil resistors have had the best precision and stability ever since they were introduced in 1958 by Felix Zandman. One of the important parameters influencing stability is the temperature coefficient of resistance (TCR). Although the TCR of foil resistors is considered extremely low, this characteristic has been further refined over the years.^[1]

Other

• Metal oxide resistor
• Cermet
• Phenolic
• Tantalum

A Cermet is a composite material composed of ceramic (cer) and metallic (met) materials. ... Phenols, sometimes called phenolics, are a class of chemical compounds consisting of a hydroxyl functional group (-OH) attached to an aromatic hydrocarbon group. ... General Name, Symbol, Number tantalum, Ta, 73 Chemical series transition metals Group, Period, Block 5, 6, d Appearance gray blue Standard atomic weight 180. ...

Noise

In precision circuits, electronic noise becomes of utmost concern. As dissipative elements, resistors will naturally produce a fluctuating "noise" voltage across their terminals. This Johnson–Nyquist noise is predicted by the Fluctuation-Dissipation theorem and is a fundamental noise source present in all resistors which must be considered in constructing low-noise electronics. For example, the gain in a simple (non-)inverting amplifier is set using a voltage divider. Noise considerations dictate that the smallest practical resistance should be used, since the noise voltage scales with resistance, and any resistor noise in the voltage divider will be impressed upon the amplifier's output. Johnson–Nyquist noise (thermal noise, Johnson noise, or Nyquist noise) is the electronic noise generated by the thermal agitation of the charge carriers (usually the electrons) inside an electrical conductor at equilibrium, which happens regardless of any applied voltage. ...

Although Johnson-Nyquist noise is a fundamental noise source, resistors frequently exhibit other, "non-fundamental" sources of noise. Noise due to these sources is called "excess noise." Thick-film and carbon composition resistors are notorious for excess noise at low frequencies. Wire-wound and thin-film resistors, though much more expensive, are often utilized for their better noise characteristics.

Failure modes and pitfalls

Like every part, resistors can fail; the usual way depends on their construction. Carbon composition resistors and metal film resistors typically fail as open circuits. Carbon-film resistors typically fail as short circuits.

Various effects become important in high-precision applications. Small voltage differentials may appear on the resistors due to thermoelectric effect if their ends are not kept at the same temperature. The voltages appear in the junctions of the resistor leads with the circuit board and with the resistor body. Common metal film resistors show such effect at magnitude of about 20 µV/°C. Some carbon composition resistors can go as high as 400 µV/°C, and specially constructed resistors can go as low as 0.05 µV/°C. In applications where thermoelectric effects may become important, care has to be taken to e.g. mount the resistors horizontally to avoid temperature gradients and to mind the air flow over the board. ^[2] The Peltier–Seebeck effect, or thermoelectric effect, is the direct conversion of heat differentials to electric voltage and vice versa. ...

See also

• Electronic Components
• Electronic Devices and Circuits
• Johnson-Nyquist noise
• Potentiometer
• Resistivity
• Resistors in series and parallel circuits
• Shot noise
• Thermistor
• Wikibooks:Electronics:Component Identification

Objects used in tandem with electricity. ... The process of circuit design can cover systems ranging from national power grids all the way down to the individual transistors within an integrated circuit. ... Johnson-Nyquist noise, thermal noise, Johnson noise, or Nyquist noise) is the noise generated by the equilibrium fluctuations of the electric current inside an electrical conductor, which happens regardless of any applied voltage, due to the random thermal motion of the charge carriers (the electrons). ... It has been suggested that Determining emf of primary cells using potentiometer be merged into this article or section. ... Electrical resistivity (also known as specific electrical resistance) is a measure of how strongly a material opposes the flow of electric current. ... Electrical circuit components can be connected together in one of two ways: series or parallel. ... Photon noise simulation. ... NTC thermistor, bead type, insulated wires Thermistor symbol A thermistor is a type of resistor used to measure temperature changes, relying on the change in its resistance with changing temperature. ...

References

External links

Wikimedia Commons has media related to:

Resistors

• 4-terminal resistors - How ultra-precise resistors work
• Beginner's guide to potentiometers, including description of different tapers
• Aspects of resistors, including materials, tapers, and color code
• Color Coded Resistance Calculator
• Resistor Types - Does It Matter?
• Ask The Applications Engineer - Difference between types of resistors
• Resistors and their uses
• A very well illustrated tutorial about Resistors, Volt and Current

Image File history File links Commons-logo. ...