 A variable scale for measuring maps The scale of a map is the ratio of a single unit of distance on the map to the equivalent distance on the ground. The scale can be expressed in four ways: as a ratio, a fraction, in words and as a graphical (bar) scale. Image File history File linksMetadata Download high-resolution version (1950x1782, 182 KB) File links The following pages on the English Wikipedia link to this file (pages on other projects are not listed): Scale (map) Metadata This file contains additional information, probably added from the digital camera or scanner used to...
Image File history File linksMetadata Download high-resolution version (1950x1782, 182 KB) File links The following pages on the English Wikipedia link to this file (pages on other projects are not listed): Scale (map) Metadata This file contains additional information, probably added from the digital camera or scanner used to...
For other uses, see Map (disambiguation). ...
In common usage a fraction is any part of a unit. ...
A scale expressed as a ratio of say 1:25,000 means that one unit on the map represents 25,000 units on the ground, ie 1 millimetre represents 25,000 mm, expressed better as 25 metres.
The statement 'one millimetre represents 25 metres' is an expression of scale in words.
Scale expressed as a fraction, 1/25,000, means that any distance on the map is 1/25,000 th the distance on the ground. It expresses the amount of reduction of distances used to represent detail on the map. The 25,000 value is called the scale denominator.
Due to showing the curved surface of the earth on a flat map surface, the scale varies from place to place. Thus a representative fraction is stated for scale which is correct at the centre of the map and which varies elsewhere. While called representative fraction, it really is the representative ratio. This article is about Earth as a planet. ...
A graphical (bar) scale is a ruler with ground distances added, included in the margin of most maps. The graphical scale is used to measure distances on the map. The distance on the map is marked on the edge of a sheet of paper, which is then placed over the graphical bar scale and the distance read.
Maps are usually produced at standard scales of (say) 1:10,000, 1:25,000, 1:50,000, 1:100,000, 1:250,000, 1:500,000. The distance on the ground equals the distance measured on the map multiplied by the scale denominator.
Calculation: Measure 466 mm on a map with scale 1:50,000 466 x 50,000 = 23,300,000 mm ie 23,300 metres ie 23.3 kilometres Some older maps use imperial units expressed in words, such as 60 chains to 1 inch or 2 miles to 1 inch, etc. The Imperial units or the Imperial system is a collection of English units, first defined in the Weights and Measures Act of 1824, later refined (until 1959) and reduced. ...
In this case measure mm on the map and multiply by the scale factor below (where 1 yard = 36 inches, 1 chain = 22 yards) ... As a unit of measurement within the Imperial system, the chain (surveyors chain, Gunters chain) is defined as 22 yards, 66 feet, or four rods. ...
40 chains = 1 inch >> 40 x 22 x 36 >> 1 : 31,680 (scale) 60 chains = 1 inch >> 60 x 22 x 36 >> 1 : 47,520 (scale) 1 mile = 1 inch >> 63,360 x 1 >> 1 : 63,360 (scale) 2 miles = 1 inch >> 63,360 x 2 >> 1 : 126,720 (scale) 4 miles = 1 inch >> 63,360 x 4 >> 1 : 253,440 (scale) Calculation: Measure 132 mm on a map with scale 60 chains to 1 inch 132 x 47,520 = 6272,640 milimetres ie 6,272.6 metres ie 6.27 kilometres Maps are sometimes referred to by relative descriptions of large scale or small scale. A large scale map displays objects so they appear relatively large. For example, an island displayed on a 1:10,000 map will appear larger than if displayed on a 1:100,000 map. Thus, the former is large scale. Maps with a ratio of 1:50,000 or larger (for example, 1:25,000 would be larger) are considered large scale. Maps with a ratio of 1:50,000 to 1:250,000 are considered medium scale. Any maps with a smaller scale (for example 1:500,000) are considered small scale.[1] A trick to remember this sometimes unintuitive description schema is to remember that small scales have tiny ratio values (i.e. 1:500000 = 1/500000 = 0.000002) and large scales have larger ratio values (1:500 = 1/500 = 0.002).
[2]
See also
Wikimedia Commons has media related to: scale Image File history File links Commons-logo. ...
An architects scale is a specialized ruler. ...
B.O.L.T.S.S. is an acronym used in high-school school geography education, which shows the standard information to include in a map (other than the map itself). ...
An engineers scale is a ruler, a tool for measuring distances. ...
The concept of scale is applicable if a system is represented proportionally by another system. ...
lol rofl taco hahaThere is also a nscale factor for the expansion of the Universe Scale factors are used in computer science when certain real world numbers need to be represented on a different scale in order to fit a required number format. ...
Vertical exaggeration (VE) is a scale that is used in raised-relief maps, plans and technical drawings (cross section perspectives). ...
References
External links |
Feeds |
Contact