A tremolo arm, tremolo bar, vibrato bar, whammy bar, or wang bar is a lever attached to the bridge and/or the tailpiece of an electric guitar or archtop guitar to enable the player to quickly vary the tension and sometimes the length of the strings temporarily, changing the pitch to create a vibrato, portamento or pitch bend effect. Instruments without this device are called hard-tail. The term vibrola is also used by some guitar makers to describe their particular tremolo arm designs. A Violin Bridge blank and finished bridge A bridge is a device for supporting the strings on a stringed instrument and transmitting the vibration of those strings to some other structural component of the instrument in order to transfer the sound to the surrounding air balls. ... The tailpiece is an element found in all musical instruments of the violin family. ... An electric guitar is a type of guitar that uses pickups to convert the vibration of its steel-cored strings into electrical current, which is then amplified. ... Epiphone Emperor, an archtop design. ... Pitch is the perceived fundamental frequency of a sound. ... Vibrato is a musical effect where the pitch or frequency of a note or sound is quickly and repeatedly raised and lowered over a small distance for the duration of that note or sound. ... Portamento is a musical term currently used to mean pitch bending or sliding, and in 16th century polyphonic writing refers to a type of musical ornamentation. ... Portamento is a musical term currently used to mean pitch bending or sliding, and in 16th century polyphonic writing refers to a type of musical ornamentation. ...

Closeup of a Squier Stratocaster, showing the two-point synchronized tremolo found on most current higher-end Fender guitars. Some other current Stratocaster models still use the older classic system, while still others use the licensed locking trem.

The tremolo arm began as a mechanical device for more easily producing the vibrato effects that blues and jazz guitarists had long produced on arch top guitars by manipulating the tailpiece with their picking hand. However, it has also made many sounds possible that could not be produced by the old technique. detail of the body of a Stratocaster Copyright (c) 2004 David Monniaux File history Legend: (cur) = this is the current file, (del) = delete this old version, (rev) = revert to this old version. ... detail of the body of a Stratocaster Copyright (c) 2004 David Monniaux File history Legend: (cur) = this is the current file, (del) = delete this old version, (rev) = revert to this old version. ... Squier is a second-line brand of the Fender Musical Instruments Corporation. ... A Fender Stratocaster with rosewood fingerboard and three-tone sunburst finish. ... Vibrato is a musical effect where the pitch or frequency of a note or sound is quickly and repeatedly raised and lowered over a small distance for the duration of that note or sound. ... Blues music redirects here. ... Jazz guitar refers to the use of guitar in jazz music. ... Archtop guitars are steel-stringed acoustic guitars with a distinctive arched belly and a sound particularly suited to blues guitar and jazz. ... The tailpiece is an element found in all musical instruments of the violin family. ...

Since the regular appearance of mechanical tremolo arms in the 1950s, artists such as Jimi Hendrix, Kevin Shields, Jeff Beck, Lonnie Mack, Ritchie Blackmore, Steve Lukather, Eddie Van Halen, Duane Eddy, Dimebag Darrell, David Gilmour, Hank Marvin, Jimmy Page, Randy Rhoads, Joe Satriani, Steve Vai, K.K. Downing, Brian May, Richie Sambora, and many surf music bands have used the tremolo to great effect, and the effects they created using it have become a recognized part of many styles of electric guitar. Jimi Hendrix (November 27, 1942 – September 18, 1970) was an American guitar virtuoso, singer and songwriter. ... Kevin Shields (born Queens, New York City, USA on May 21, 1963) is a singer, guitarist, and producer who fronted the London-based band My Bloody Valentine in the late 1980s and early 1990s. ... Geoffrey Arnold (Jeff) Beck (born June 24, 1944 to Arnold and Ethel Beck in Wallington, Greater London) is an English rock guitarist. ... Lonnie Mack (born Lonnie McIntosh, 18 July 1941, Harrison, Indiana) is an influential rock and blues guitarist. ... Richard Hugh Blackmore, (born 14 April 1945) is an English guitarist. ... Steve Luke Lukather (born Steven Lee Lukather on October 21, 1957 in San Fernando Valley, California, USA) is an American Grammy Award winning singer, songwriter, arranger, producer and guitar player, best known for his work with the rock band Toto. ... Edward Van Halen (born Edward Lodewijk van Halen on January 26, 1955[1] in Nijmegen, Netherlands), is a guitarist, keyboardist, songwriter and producer most famous for being the lead guitarist and a co-founder of the hard rock band, Van Halen. ... Duane Eddy (born April 26, 1938), is a Grammy winning guitarist. ... “Dimebag” redirects here. ... David Jon Gilmour CBE (born March 6, 1946 in Cambridge) is an English musician best known as a guitarist, singer, and songwriter in the band Pink Floyd. ... Brian Robson Rankin (born 28 October 1941), better known by the stage name Hank B. Marvin, is the English lead guitarist for the band The Shadows. ... James Patrick Jimmy Page, OBE (born 9 January 1944) is an English guitarist, composer and record producer. ... For the talk radio host, see Randi Rhodes. ... Joseph Satch Satriani (born on July 15, 1956, in Westbury, New York, U.S.) is an American guitarist and former guitar instructor. ... Steven Steve Siro Vai (born June 6, 1960 in Carle Place, New York) is a Grammy Award winning guitarist, composer, vocalist, and record producer. ... K.K. Downing of Judas Priest K.K. Downing was born as Kenneth Downing on October 27, 1951 in Walsall, England. ... For the Australian film composer, see Brian May (composer). ... Richard Stephen Sambora (born on July 11th, 1959), is an American rock guitarist, singer and songwriter who is the lead guitarist of the rock band Bon Jovi. ... Surf music is a genre of popular music associated with surf culture. ...

Naming argument and controversy

Traditionally, electric guitarists have reversed the normal meanings of the terms vibrato and tremolo when referring to hardware devices and the effects they produce. While the tremolo arm can produce variations of pitch including what is normally termed vibrato, it can never produce the effect normally known as tremolo (modulation of volume). Tremolo, on the other hand, is exactly the effect produced by the vibrato units built in to many classic guitar amplifiers. Pitch is the perceived fundamental frequency of a sound. ... Vibrato is a musical effect where the pitch or frequency of a note or sound is quickly and repeatedly raised and lowered over a small distance for the duration of that note or sound. ... Tremolo is a musical term with two meanings: A rapid repetition of the same note, a rapid variation in the amplitude of a single note, or an alternation between two or more notes. ... A vibrato unit is an effects unit used to modify the sound of an electric guitar by producing a regular variation in the amplitude of the sound. ... A guitar combo amplifier A guitar amplifier is an electronic amplifier designed for use with an electric or electronic musical instrument, such as an electric guitar. ...

This reversal of terminology is generally attributed to Leo Fender and the naming of the Fender 'Vibroverb' amplifier, which actually used tremolo (rapid volume changes) in an attempt to create a vibrato-like (rapid changes in pitch) sound. See vibrato unit for details of the history of these terms in relation to electric guitar, and related issues. In this article, the words are used interchangeably. Image:Leo Fender tinkering. ... A vibrato unit is an effects unit used to modify the sound of an electric guitar by producing a regular variation in the amplitude of the sound. ...

Notable mechanism designs

Almost all tremolo arms are based on one or more of four basic designs:

• The Bigsby vibrato tailpiece.
• The Fender synchronized tremolo.
• The Fender floating tremolo.
• The Floyd Rose floating tremolo.
• The Ibanez Edge System.

Origin of the vibrato tailpiece

One of the first mechanical tremolo/vibrato units (although not hand-operated) was the Kauffman Vibrato as used on Rickenbacker Vibrola Spanish guitars. They were not operated by hand, but rather moved with an electrical mechanism. It was developed by Doc Kauffman to simulate the pitch manipulation available with steel guitars. A hand operated unit was later created and used on Rickenbacker's Capri line of guitars in the '50's, such as John Lennon's '58 325. It was a side-to-side action vibrato unit (rather than the up-down action of later units) that was notorious for throwing the guitar out of tune, hence John's replacing it with a Bigsby B5. Thankfully, it was replaced by the Ac'cent Vibrola, which used no coiled springs to change tension, giving it less chance to throw the guitar out of tune.

Bigsby

Epiphone Casino VT with Bigsby.

Main article: Bigsby

The first commercially successful tremolo arm was the Bigsby vibrato tailpiece, most often just called a Bigsby, and invented by Paul Bigsby. The exact date of its first availability is uncertain, as Bigsby kept few records, but it was on Bigsby-built guitars photographed in 1952, in what became its standard form. In several interviews, the late Merle Travis, for whom Bigsby designed his first vibrato, recalled the prototype as being built for him in the "late '40's". The design uses a spring-loaded arm that rotates a cylindrical bar in the tailpiece, varying the string tension to create vibrato and other pitch variations. The string tension is balanced against a single, short helical compression spring, positioned under the arm pivot. Pioneering blues-rock guitarist Lonnie Mack was known for using a Bigsby on his famous 1958 Gibson "Flying V". The term "whammy bar" is believed to derive from Mack's 1963 instrumental hit, "Wham!", in which Mack made liberal use of the Bigsby. Image File history File linksMetadata Download high resolution version (671x1592, 353 KB) Oggetto Description: Epiphone Casino VT Made by User:Maxo Licensing File links The following pages link to this file: Tremolo arm Metadata This file contains additional information, probably added from the digital camera or scanner used to create... Image File history File linksMetadata Download high resolution version (671x1592, 353 KB) Oggetto Description: Epiphone Casino VT Made by User:Maxo Licensing File links The following pages link to this file: Tremolo arm Metadata This file contains additional information, probably added from the digital camera or scanner used to create... Epiphone Emperor The Epiphone Company is a guitar manufacturer. ... The Bigsby vibrato tailpiece (or Bigsby for short) is a type of vibrato device for electric guitar designed by its namesake Paul A. Bigsby. ... The Bigsby vibrato tailpiece (or Bigsby for short) is a type of vibrato device for electric guitar designed by its namesake Paul A. Bigsby. ... Paul A. Bigsby was the designer of the Bigsby tremolo arm and proprieter of Bigsby Guitars. ... Merle Travis (November 29, 1917 - October 20, 1983) is an American country and western singer, songwriter, and musician. ... Physical compression is the result of the subjection of a material to compressive stress, resulting in reduction of volume. ... For other uses, see Spring. ... Blues Rock or Blues-rock is a fusion genre of music which combines elements of the blues with rock and roll. ... Lonnie Mack (born Lonnie McIntosh, 18 July 1941, Harrison, Indiana) is an influential rock and blues guitarist. ...

To this day, the Bigsby enjoys some popularity, especially on hollow body guitars, and is available as a factory-fitted option on top-line models both hollow and solid bodied from many makers, and as an aftermarket addition (requiring some skill to fit however). It remains the only widely used design whose mechanism is entirely above the belly of the guitar body, making it the only design particularly suitable for acoustic and semi-acoustic guitars.

Fender synchronized tremolo

Sketch of Fender synchronized tremolo from 1954 patent application

After the Bigsby, the next major development was Leo Fender's synchronized tremolo, the device which introduced the term tremolo arm. First released in 1954 on Fender's first legendary Stratocaster, the simple but effective design offers a greater range of pitch change than the Bigsby, and particularly a better capability for upbends. Image File history File links Size of this preview: 364 × 599 pixelsFull resolution (1696 × 2790 pixels, file size: 728 KB, MIME type: image/png) Other versions Cslpat2. ... Image File history File links Size of this preview: 364 × 599 pixelsFull resolution (1696 × 2790 pixels, file size: 728 KB, MIME type: image/png) Other versions Cslpat2. ... Image:Leo Fender tinkering. ... It has been suggested that Fender Amplifier History be merged into this article or section. ... A Fender Stratocaster with rosewood fingerboard and three-tone sunburst finish. ...

The basis of the synchronized tremolo is a rigid assembly incorporating both the bridge and tailpiece which is pivoted on the guitar belly. In the original design, this was based on the principle of the 'knife edge' balance. A bevel on the front underside of a steel top plate formed a very wide angle knife edge that rested on the top surface of the guitar body. A small imbalance in tension between the pull of the strings and the counterbalancing pull of the tremolo springs held the pivot edge firmly in place against the body. Six hardened steel woodscrews passing through slightly oversize holes just in front of the pivot point, stopped the bridge from being pulled towards the neck end of the guitar. The upper portion of the screws is smooth, not threaded. These six screws are often mistakenly assumed to be the pivot point rather than the hidden knife edge. This design works, in spite of the friction caused by the edges of the six holes sliding up and down the screw shafts when vibrato is applied.

Back of a Stratocaster copy, showing the mechanism. Note the six coloured string end ferules visible at the bottoms of the holes, through which the strings are threaded from the back.

The bridge is formed by six bridge saddles held against this plate by string tension, and individually adjustable both for height and intonation. The tailpiece consists of a solid block of metal, mounted behind the tremolo plate and secured to it by three machine screws, and passing right through the guitar body. In a chamber routed into the back of the guitar are up to five (normally three) long coil springs which connect to the back of the tailpiece block, and whose tension balances that of the strings. The tremolo arm also passes through the tremolo plate and tailpiece block, providing direct and rigid connection. Image File history File links Download high resolution version (1455x1031, 100 KB) Summary Photo of the back of a stratocaster copy showing the tremolo arm mechanism. ... Image File history File links Download high resolution version (1455x1031, 100 KB) Summary Photo of the back of a stratocaster copy showing the tremolo arm mechanism. ... A Fender Stratocaster with rosewood fingerboard and three-tone sunburst finish. ... A compression coil spring A tension coil spring A selection of conical coil springs A Coil spring, also known as a helical spring, is a mechanical device, which is typically used to store energy and subsequently release it, to absorb shock, or to maintain a force between contacting surfaces. ...

Ignoring the bridge adjustments, this mechanism has only two moving parts, one of them the arm itself, the same as the Bigsby. But unlike the Bigsby, the synchronized tremolo moves the bridge as well as the tailpiece, varying both the length and tension of the strings.

Detail of the strat style trem. Note that there is provision for up to five springs. Only three are fitted here to allow for use of light strings, there being no other adjustment.

The strings pass through the body of the guitar, in similar fashion to the Fender Telecaster. When changing strings the new string is threaded through the body from the back. However, in the Telecaster the ferrule end is held by a collar firmly anchored to the guitar body; In the Stratocaster, it is held by the moving metal block through which the strings pass. Image File history File links Strat_trem. ... Image File history File links Strat_trem. ... The Fender Telecaster, also known as a Tele, is a typically dual-pickup, solid-body electric guitar made by Fender. ...

The Stratocaster tremolo, often just called the Strat trem, or also called the whammy bar, is the most copied tremolo unit. Similar pattern units appear on many solid-body guitars by various makers. Its design has been the basis of the premium Fender tremolo known as the two-point synchronised tremolo, and also of the Floyd Rose locking tremolo, see below. Both the original Stratocaster tremolo, sometimes called the synchronous tremolo and sometimes the vintage synchronized tremolo, and derived designs such as the two-point and Floyd Rose appear on current models as of 2007.

This preeminence of the synchronised tremolo was finally established by the use of Stratocaster guitars by Jimi Hendrix, Pete Townshend and others towards the end of the 1960s. Throughout the 1960s, the premium Fender guitars were the Jaguar range, equipped with the floating tremolo. By the early 1970s, it was obvious that most guitarists preferred the cheaper Stratocaster, regardless of price and supposed quality and prestige, and particularly liked its tremolo arm design. The Jaguar and indeed all other Fender guitars using any tremolo design other than the synchronised tremolo were for a time withdrawn, to return to the catalog as classic or retro models in the 1990s. Jimi Hendrix (November 27, 1942 – September 18, 1970) was an American guitar virtuoso, singer and songwriter. ... Peter Dennis Blandford Townshend (born May 19, 1945 in Chiswick, London), is an award-winning English rock guitarist, singer, songwriter, and composer. ... The Fender Jaguar is an electric guitar that was introduced in 1962. ... A Fender Stratocaster with rosewood fingerboard and three-tone sunburst finish. ...

Fender floating bridge

The floating bridge featured on two Fender tremolo arm designs, both developed by Leo Fender subsequently to the original synchronised tremolo but overshadowed by it. Despite its not being the most popular bridge, there are side benefits unique to guitars with this type of bridge. See 3rd bridge guitars. Fred Frith displaying some of his homemade 3rd bridge guitars, circa 1982. ...

Floating tremolo

Fender floating tremolo tailpiece and floating bridge on a Jazzmaster

The floating tremolo was designed by Fender for the Fender Jazzmaster, and first appeared with the release of the Jazzmaster in 1958. A larger, heavier and more complex mechanism than the synchronised tremolo, and promoted over it by Fender as their premium tremolo arm mechanism, it never achieved the same popularity, though if properly set up according to Fender's recommendations, it held tune as well or better than the synchronized vibrato unit. Image File history File linksMetadata Download high resolution version (562x749, 27 KB) Summary from http://nl. ... Image File history File linksMetadata Download high resolution version (562x749, 27 KB) Summary from http://nl. ... 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ... 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ... 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ...

The main superficial difference is that, while much of the mechanism of the synchronised tremolo including the springs is accessed by removing a rectangular plate in the back of the guitar body, and is mounted on the guitar body in a routed bay extending behind the pickups, the entire mechanism of the floating tremolo is mounted on a roughly triangular chromed plate in the front of the guitar body, on the opposite side of the bridge to the pickups. The string tension is balanced against a single short helical spring, in compression rather than tension, mounted on the back of the tremolo mounting plate. The spring is adjustable by turning a screw located towards the center of this plate. Physical compression is the result of the subjection of a material to compressive stress, resulting in reduction of volume. ... Tension is a reaction force applied by a stretched string (rope or a similar object) on the objects which stretch it. ...

The ferrule ends of the strings are held on the top of the guitar in a tailpiece plate called the knife plate which emerges from the mechanism, rather than the strings vanishing into the mechanism as with the synchronized tremolo. It is the knife plate that is moved when the tremolo arm is operated. Unlike the synchronized tremolo, the bridge is not moved directly by the mechanism, but only by the movement of the strings, and is allowed to tilt to accommodate this movement. This is called a floating bridge.

The Fender floating tremolo also features a knob that enables the player to lock and thus disable the tremolo mechanism, allowing quick recovery of tuning in the event of breaking one string, and providing tuning stability with the mechanism locked that was intended to be similar to that of a fixed bridge guitar. In practice, this stability was not generally achieved, leading some players to replace the mechanism with a fixed bridge and tailpiece to produce a high quality "hard-tail" solid body guitar not otherwise available at the time.

The floating tremolo was greatly favored by some surf music bands, particularly for its ability to produce a pronounced and distinctive vibrato on a sustained chord without disturbing the tuning of the guitar. To fully achieve this benefit however, correct setup, as per Fender's recommendations, was essential. Surf music is a genre of popular music associated with surf culture. ...

An issue with the unit was the bridge itself, which Leo Fender over-engineered. The six individual bridge saddles were multi-grooved "barrels". The individual barrels were not grooved deeply enough for secure holding of the strings in heavy pick attack, and each barrel had a tiny adjustment screw at each end. Adding the intonation adjustment screws, and the screws at each end of the bridge saddle to raise or lower the bridge as a whole, gave the bridge twenty separate adjustment possibilities. The great majority of players found this much too "fiddly", and, adding the tendency of the strings to jump out of their individual saddles in aggressive playing, the overall reception was rather lukewarm for what was essentially an excellent - but over-engineered - design. Later, many players of the Jazzmaster and Jaguar found that the bridge on these instruments could be replaced with no retrofitting by the standard bridge from the Fender Mustang (below), which eliminated several of the worst problems with the original bridge.

In addition to the Jazzmaster, the floating tremolo was used on the then top of the line Fender Jaguar guitars, released in 1962, and also on the early Fender Bass VI, released in 1961. Bridges are not interchangeable between these three models, the Jaguar bridge having longer 'legs' to cater for its higher pickups, and the Bass VI saddles being cut for larger diameter strings. There have also been a small number of not very notable imitations by other makers, generally without the locking knob. 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ... The Fender Jaguar is an electric guitar that was introduced in 1962. ... A Fender VI on a stand The Fender Bass VI, originally known as the Fender VI, is a six-string electric bass by Fender. ...

Fender discontinued all floating tremolo models in the 1970s, but reintroduced both the Jazzmaster and Jaguar in 1999, and the tremolo-equipped Bass VI in 2006. 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ...

Dynamic Vibrato

Fender Mustang tremolo arm

The Fender Dynamic Vibrato, also known as the Mustang tremolo or Mustang trem, was introduced in 1964 on the Fender Mustang, intended as a student model. It was also notably used on the Jagstang, a custom design by Kurt Cobain combining features of the Jaguar and the Mustang. Some late 1960s Mustangs were fitted instead with the floating tremolo, which was promoted by Fender as their premium unit, but later Mustangs returned to the Dynamic Vibrato. Image File history File links Mustang_trem. ... Image File history File links Mustang_trem. ... The Fender Mustang is an electric guitar by the Fender Musical Instruments Company, introduced in 1964 as the basis of a major redesign of Fenders student models then consisting of the Musicmaster and Duo-Sonic. ... The Fender Mustang is an electric guitar by the Fender Musical Instruments Company, introduced in 1964 as the basis of a major redesign of Fenders student models then consisting of the Musicmaster and Duo-Sonic. ... The Jag-Stang is a hybrid of two Fender electric guitars: a Jaguar and a Mustang. ... Kurt Donald Cobain (February 20, 1967 – c. ...

The Dynamic Vibrato is still preferred by some lead guitarists above all other designs. It features a floating bridge similar to that of the floating tremolo, but the bridge is integral with the tremolo unit, unlike that of the floating tremolo which is mounted separately. The strings are controlled by a tailpiece bar to which the tremolo arm is visibly connected, similar to the Bigsby, and the mechanism is installed from the top of the instrument, similar to the floating tremolo. It combines some features of all three basic designs. Lead guitar refers to a role within a band, that provides melody or melodic material, as opposed to the rhythm of the rhythm guitar, bass, and drums. ...

The Dynamic Vibrato is often confused with the Fender floating tremolo, to which it bears some resemblance. The original production runs of the two overlap by more than a decade, but the mechanisms are quite different. The existence of a few 1960s Mustangs factory fitted with the floating tremolo has probably added to the confusion. The concealed mechanism is in a chamber of a completely different shape and position, requiring an impractical amount of woodwork to convert from one to the other, and the mounting plate is of a different shape with different mounting holes.

The string tension is balanced against two medium length hellical springs under tension, mounted on the underside of the tremolo mounting plate, one attached to each of the two feet of the tailpiece bar.

Dynamic Vibrato units may be recognised by the integrated floating bridge and the stamps "Fender" and "DYNAMIC VIBRATO". Many but not all units also have the words "PAT PEND" or "PAT. NO. 3,241,418" stamped under the word "Fender".

The Dynamic Vibrato was the last of the floating bridge designs to be discontinued by Fender, with the Mustang in 1982, and the first to be reintroduced, again with the Mustang, in 1990.

Gibson Vibrola

Maestro Vibrola long tailpiece fitted to a Gibson SG.

Gibson have marketed a number of tremolo arm designs under the name Vibrola. Image File history File linksMetadata SG_LPbody3. ... Image File history File linksMetadata SG_LPbody3. ... The Gibson SG is a popular model of solid-bodied electric guitar that was introduced in the early 1960s. ... The Gibson Guitar Corporation, of Nashville, Tennessee, USA, is one of the worlds best-known manufacturers of acoustic and electric guitars. ... A tremolo arm, tremolo bar or whammy bar is a lever attached to the bridge and/or the tailpiece of an electric guitar to enable the player to quickly vary the tension and sometimes the length of the strings temporarily, changing the pitch to create a vibrato, portamento or pitch...

Vibrola tailpieces include a licensed version of the Bigsby and several in-house Gibson designs. The Gibson designs did not have the impact of the Bigsby and Fender designs, and have inspired few if any copies, but they competed reasonably successfully and continue to sell, with artists such as Jimi Hendrix and Eric Clapton and using them from time to time during the 1960s, and many working musicians using them to this day. The tailpiece is an element found in all musical instruments of the violin family. ... The Bigsby vibrato tailpiece (or Bigsby for short) is a type of vibrato device for electric guitar designed by its namesake Paul A. Bigsby. ... Jimi Hendrix (November 27, 1942 – September 18, 1970) was an American guitar virtuoso, singer and songwriter. ... Eric Patrick Clapton CBE (born 30 March 1945), nicknamed Slowhand, is a Grammy Award winning English guitarist, singer, songwriter and composer. ...

Gibson designs tend to have the mechanism above the belly of the guitar, similar to the Bigsby, and are therefore equally suitable for use on acoustic guitars and especially archtops. This reflects the Gibson company's history as the developer of the archtop and their continued strength and focus in this market, but carries over even to designs used only on solid body guitars, such as the Short Lyre Vibrola used on some Flying V and SG models. While these do require some woodwork to install them, some more so than others, there is nothing like the extensive body routing required for all of the Fender trems. A steel string acoustic guitar is a modern form of guitar descended from the classical guitar, but strung with steel strings for a brighter, louder sound. ... Epiphone Emperor, an archtop design. ... The Gibson Flying V is an electric guitar model first released by Gibson in 1958. ... The Gibson SG is a popular model of solid-bodied electric guitar that was introduced in the early 1960s. ...

The earliest of the Gibson-designed tremolo arms was a distinctive long tailpiece released as the Gibson Vibrato in 1962 on some SG models. This mechanism later became known as the side vibrato because of the position of the lever which emerged from the side of the long tailpiece. This lever had only restricted movement up and down in a plane close to that of the strings, so its action was unlike that of the Bigsby and Fender units, and remains unique. It was also described as the Gibson Vibrola Tailpiece in Gibson documents, but this name can be applied to any of the Gibson tremolo mechanisms. It was not a success and is of interest mainly to historians and collectors. The tailpiece is an element found in all musical instruments of the violin family. ... The Gibson SG is a popular model of solid-bodied electric guitar that was introduced in the early 1960s. ...

The Deluxe Gibson Vibrato, released in 1963, was another long tailpiece mechanism, and replaced the Gibson Vibrato. Its tremolo arm and all subsequent designs used the action adopted by Bigsby and Fender. As the Deluxe Gibson Vibrola a short version of it was fitted as standard to the 1967 reissue Gibson Flying V. Two other long tailpiece designs, superficially similar to the Deluxe Gibson Vibrato, are the Lyre Vibrola which was being fitted to Gibson ES-335s as an option by 1964 and is engraved with a lyre motif, and the Maestro Vibrola which was an option on the ES-335 by 1967. The Gibson Flying V is an electric guitar model first released by Gibson in 1958. ... The Gibson ES-335 was the worlds first commercial semi-hollowbody electric guitar, released by Gibson Guitar Corporation in 1958. ... “Lyres” redirects here. ...

Most Vibrola tailpieces, including the Bigsby, Lyre and Maestro, exist in both long and short versions. The long version replaces a trapeze-style tailpiece, such as found on most archtop guitars, and transmits the string tension to the guitar side. The short version replaces a string stop style tailpiece, such as found on the original Gibson Les Paul, and transmits the string tension to the guitar belly, so short versions are generally used only on solid body guitars. Long tailpieces can be used on almost any guitar (an exception being the Gibson Flying V where there is no room for one), and both long and short versions have been used on various models of Gibson SG and Gibson Les Paul guitars. Epiphone Emperor, an archtop design. ... The Gibson Les Paul is one of the most recognizable solid-body electric guitar designs in the world. ... The Gibson Flying V is an electric guitar model first released by Gibson in 1958. ... The Gibson SG is a popular model of solid-bodied electric guitar that was introduced in the early 1960s. ... The Gibson Les Paul is one of the most recognizable solid-body electric guitar designs in the world. ...

None of the Gibson designs were suitable for creating the more extreme sounds that the Strat trem and its derivatives made possible. They have almost always been offered as extra cost options on guitars which sold better in non-tremolo versions. As a result, some versions are rare and command high prices from restorers and collectors. Gibson encourages this trend by refusing to sell reissue units as parts, offering them only on complete guitars (a policy similar to most guitar manufacturers).

As of 2006 Gibson was continuing to offer Vibrola units as options on many models, but also offered a few Fender-inspired tremolo arms such as the Floyd Rose on some Gibson branded guitars (Nighthawk, M3), and a wider variety through their Kramer and Epiphone brands. Kramer have always fitted Floyd Rose trems as standard and this association continues. See also rivalry between Fender and Gibson. 2006 is a common year starting on Sunday of the Gregorian calendar. ... The Gibson Nighthawk was a short lived guitar model line by guitar manufacturer, Gibson. ... This article or section does not cite any references or sources. ... Epiphone Emperor The Epiphone Company is a guitar manufacturer. ... Floyd Rose Original Floyd Rose is the organization that licenses, distributes and manufactures the Floyd Rose Locking Tremolo invented by Floyd D. Rose. ...

Fender two-point synchronized tremolo

The synchronized tremolo has been further developed by Fender to produce the two-point synchronized tremolo. This is not a locking tremolo, but is often confused with the similarly-named Floyd Rose two-point locking tremolo. The two systems are both developments of the original Stratocaster tremolo mechanism, but use the words two point to describe entirely different concepts. Floyd Rose Original Floyd Rose is the organization that licenses, distributes and manufactures the Floyd Rose Locking Tremolo invented by Floyd D. Rose. ...

The Fender two-point system uses two pivot points, one at each end of the pivot, rather than a row of six as in the original Strat trem. Conceptually, such a mechanism can be achieved by removing four of the six pivot screws from a traditional Strat trem, leaving only the two at the ends of the row, and there have been magazine articles suggesting this but it is risky. In practice, both for strength and for satisfactory performance, the pivots need to be carefully engineered. In some designs the pivots are also moved further apart than the 2.2" spacing of the outermost two screws in the original, in others they are just strengthened and more carefully shaped.

Currently, the Fender two-point system is their standard and most popular design, but they also offer models with the original classic design, as well as a few models with factory-fitted licensed Bigsby units, others with licensed locking tremolo, and still others with floating bridge designs, see below.

Other Fender designs

Still another design was used on the student model Fender Bronco, released mid 1967. This was simply known as the Fender vibrato tailpiece, or sometimes the Fender steel vibrato. It was again designed by Leo Fender although he had sold the company by the time it appeared. Basically a synchronized tremolo simplified to reduce cost, it had little popularity, and as of 2005 was the only Leo Fender tremolo arm design not available on any current Fender model. The Fender Bronco was an electric guitar model produced by the Fender company from mid 1967 until 1981. ... 2005 is a common year starting on Saturday of the Gregorian calendar. ...

Other Notable Designs

Other notable tremolo designs include the Kahler, Washburn Wonderbar, Hagstrom Tremar, The Semie Mosely designed Mosrite "Vibramute" and Moseley designs, the Stetsbar, the crossed-roller bearing linear tremolo and the early Rockinger from Germany. This last company was contracted by Kramer to develop a new fine-tuning tremolo with Edward Van Halen. The Rockinger designs proved problematic and Van Halen ultimately came to favor the Floyd Rose tremolo. Semie Moseley (1935-1992) was a guitar maker and the founder of Mosrite guitars. ... Mosrite was an American guitar manufacturing company, based in Bakersfield, California, from the late 1950s to the mid 1990s Founded by Semie Moseley, Mosrite guitars were played by many rock and roll and country artists such as Kurt Cobain, Joe Maphis, Larry Collins, Buck Trent, The Ventures, the MC5, Arthur... Moseley village green Moseley is a suburb of Birmingham, England, located 2 miles to the south of the city centre. ...

The Mosrite Vibrato

Semie Moseley developed the vibrato unit used on his Mosrite guitars from the basic concept of the Bigsby vibrato, but with many engineering improvements. The entire vibrato unit is top mounted. The strings feed through six holes in the upright plate at the rear of the unit (somewhat similar to the Fender "Floating Trem") and the bridge is also rigidly mounted. But the string saddles are vertically mounted grooved "wheels" that roll with the string during vibrato usage, and also make palm muting very easy to achieve. Moseley advertised the unit as the "feather touch" vibrato, and the touch is exceptionally light with all but heavy gauge strings. Pitch stability is excellent. Moseley made two designs of the unit, the first being sand cast, with an attached string mute beneath the bridge (much like the Fender Jaguar) and a rather short handle. This he called the "Vibramute". Two year later, he slightly simplified the design, going to a die cast design, eliminating the mute (which more players complained about than favored) and lengthening the vibrato arm slightly. This incarnation, called the "Moseley", was used on all Mosrite guitars from that point on. The actual feel and response of the two different models is virtually identical, however. Moseley also designed a companion 12-string vibrato for the 12-string version of the instrument, and this may have been one of the only - if not the only - vibratos designed for use on a 12-string guitar

Locking tremolo

Floyd Rose

Floyd Rose concept, using a blade edge pivot but otherwise based on the strat trem. I is in pitch, II is a downbend, III an upbend.

Main article: Floyd Rose

Around 1979, the locking tremolo was invented by Floyd D. Rose. The locking trem became highly popular among 1980s heavy metal guitarists due to its extremely wide range of variation and tuning stability. Image File history File links Description: Principle of Floyd Rose action illustrated in simple scheme Source: scheme made by Mikhail Yakshin Date: created 2005-09-06 Author: Mikhail Yakshin (Mikhail Yakshin) Permission: GFDL Other versions of this file: none Summary Principle of Floyd Rose action illustrated in simple scheme Licensing... Image File history File links Description: Principle of Floyd Rose action illustrated in simple scheme Source: scheme made by Mikhail Yakshin Date: created 2005-09-06 Author: Mikhail Yakshin (Mikhail Yakshin) Permission: GFDL Other versions of this file: none Summary Principle of Floyd Rose action illustrated in simple scheme Licensing... Floyd Rose Original Floyd Rose is the organization that licenses, distributes and manufactures the Floyd Rose Locking Tremolo invented by Floyd D. Rose. ... Floyd D. Rose is the founder of Floyd Rose and the inventor of the Floyd Rose locking tremolo. ...

The original Floyd Rose system was similar to the Fender synchronized tremolo, but with a number of extra mechanisms. The first to be added and most obvious is a locking plate on the head nut, tightened with a hex key to fix the strings at this point after tuning. This provides extra tuning stability, particularly during use of the tremolo arm, but as an unwanted side effect it also prevents further adjustment of the pitch using the machine heads. The nut of a string instrument is a small strip or block of hard material forming a transition between the strings playing length and the tuning machines on the headstock, or the tuning pegs in the pegbox at the upper end of the fingerboard. ... Hex keys of various sizes. ... The machine heads on a Squier Stratocaster electric guitar. ...

Floyd Rose Pro kit, double locking with fine tuners . See the image description for the numbered parts.

Fine tuners have been provided as part of the bridge mechanism on all but the earliest units to allow minor retuning without unlocking the nut. Some guitarists claim that the fine tuners add an instability to tuning, and that the original non-fine-tuning Floyd Rose bridges are far superior in this respect. It is rumored, but has never been confirmed that Edward Van Halen had a part in the inclusion of the fine tuning unit. Nonetheless, a donation of a unit to Mr. Van Halen by Floyd Rose himself gave the unit instant overnight success and credibility. Still more stability was provided by the addition of a second lock on the bridge nut, making a double locking tremolo system which was still more complex to set up. The double locking design is sometimes called a two-point locking tremolo, inviting confusion with the Fender two-point synchronized tremolo which is a different concept and not a locking tremolo at all. Most locking tremolo systems currently in production are "floating" bridges, a concept first popularized by Steve Vai. Vai, wanting the ability to both lower and raise the pitch (by pulling on the bar) had a carved "lion's claw" cavity behind the bridge to allow the bridge to be raised further than normal. Guitar manufacturers prefer this type of configuration because mounting the bridge in this way is both easier for builders (because the neck does not need to be mounted on an angle when mounted within the body of the guitar) and because it increases functionality. See Floyd Rose for details. Image File history File links Summary Floyd Rose Pro (disassembled, parts numbered) Source: Floyd Rose Guitars According to Adam Reiver from Floyd Rose Guitars that Ive contacted, these images are public domain. ... Image File history File links Summary Floyd Rose Pro (disassembled, parts numbered) Source: Floyd Rose Guitars According to Adam Reiver from Floyd Rose Guitars that Ive contacted, these images are public domain. ... Edward Lodewijk Van Halen, generally known as Eddie Van Halen, (born January 26, 1955 in Nijmegen, Netherlands,) is a virtuoso guitarist, classically-trained pianist, and founding member of the hard rock band Van Halen. ... Steven Steve Siro Vai (born June 6, 1960 in Carle Place, New York) is a Grammy Award winning guitarist, composer, vocalist, and record producer. ... Floyd Rose Original Floyd Rose is the organization that licenses, distributes and manufactures the Floyd Rose Locking Tremolo invented by Floyd D. Rose. ...

Floyd Rose or Floyd Rose licensed locking tremolo units are available factory fitted on many high and low end guitars, as well as complete aftermarket retrofit kits in many different designs. Fitting the correct kit to a guitar already fitted with a compatible tremolo may be quite straightforward; On others a high level of woodworking skill may be required, or it may not be possible at all.

The Fender Deluxe Locking Tremolo (better known as Fender/Floyd Rose) is essentially a modified American 2-point tremolo bridge with locking saddles and pop-in arm. Designed by Fender and Floyd Rose himself, this type of tremolo bridge has been introduced in the early '90s on the Deluxe Plus and Ultra series guitars. The concept is primarily intended for guitarists searching for the features of a locking tremolo system without the need to perform major surgery on their instrument. Nowadays, the Fender Deluxe tremolo is available on American Deluxe, Plus, Ultra Series and many Custom Shop guitars. The whole assembly also includes a set of locking machine heads and an LSR roller nut for optimal tuning stability. Usually available in chrome, the Fender Deluxe Locking vibrato is also featured in gold and black.

Floyd Rose also produces complete guitars featuring their tremolo systems, most notably using the Speedloader system in which the head-end tuners are eliminated entirely, and all tuning is done from the bridge end of the strings. This is accomplished without sacrificing stability by employing strings that are produced to extremely fine length tolerances, essentially having two ferrule ends and no tail. As of 2006 the Speedloader system is the latest Floyd Rose design, but has yet to catch on to the degree Floyd Rose's original tremolo did. 2006 is a common year starting on Sunday of the Gregorian calendar. ...

Locking synchronized

One of the most simplified ways to have a double locking tremolo system without making any major alteration to a solid-body electric guitar can be done by using a single locking bridge, a set of locking machine heads and a low-friction LSR Roller Nut. Fender's version of this system is also known as Fender/Floyd Rose (Fender Deluxe Locking Tremolo Assembly), as it was developed in conjunction with Floyd Rose.

Other locking trems

There have been several other "locking" type tremolo systems which have been developed, but none of these have obtained the popularity that the Floyd Rose or vintage Fender tremolo systems have achieved.

The most notable of these systems is the cam-operated Kahler Double locking tremolo, which is similar in practical use, but not in design, to the Floyd Rose. The Kahler Tremolo System is bridge with a cam operated tremolo arm system for electric guitar. ...

Yet another system that emerged in the 1980s was the Steinberger TransTrem system (standing for Transposing Tremolo). The transtrem, like the Floyd Rose Speedloader, requires special strings that can only be used on the TransTrem unit. However, the TransTrem had the novel design that the bar could be pushed in to "transpose" the tuning of the entire unit to various other keys. The system saw limited use (mainly due to its exorbitant price and limited string availability), although Edward Van Halen has continued to experiment with the system. Notable Van Halen songs where the TransTrem can be heard include "Get Up" and "Summer Nights", from the album 5150. Edward Lodewijk Van Halen, generally known as Eddie Van Halen, (born January 26, 1955 in Nijmegen, Netherlands,) is a virtuoso guitarist, classically-trained pianist, and founding member of the hard rock band Van Halen. ... 5150 is the seventh album by American hard rock band Van Halen, released in 1986. ...

Examples

Notable tracks

The electric guitar is an instrument of unique sounds. The ability to completely detune the instrument and pull it back on the fly is possible with the 'tremolo bar'. Many notable guitar players have used this effect over the years.

Early in electric guitar history, Chet Atkins favored the Bigsby unit, and it can be heard - occasionally - being tastefully used by him in a number of his recordings. Generally, Atkins used the Bigsby just to "dip" chords. His recording of "It Don't Mean a Thing if it Ain't Got That Swing" with Les Paul (another Bigsby user) is a typical example of how Atkins used the device. Chet Atkins Chester Burton Chet Atkins (June 20, 1924 – June 30, 2001) was an influential guitarist and record producer. ... This article is about the musician. ...

Surf and early rock instrumental guitar is synonymous with vibrato use. Duane Eddy established the "twangy guitar" sound with a Bigsby vibrato on his Gretsch guitar. Classic examples of this are his recordings of "Rebel Rouser" and "Peter Gunn". Both "Perfidia" and "Walk Don't Run" by the Ventures are also typical examples Duane Eddy (born April 26, 1938), is a Grammy winning guitarist. ...

Prior to Jimi Hendrix, many guitarists used the Fender or Bigsby vibrato to approximate the pedal steel or slide guitar tones found in Hawaiian or Country music. This early vibrato was actuated after striking chords or individual notes; lowering or modulating the pitch as the notes decayed. Hendrix completely rewrote the book on vibrato; using it while picking, hammering on, pulling off and with harmonics and feedback tones. His intense use led to problems staying in tune which he could compensate for (to some degree) by exerting tremendous right hand strength and bending individual strings within a chord back in tune. To emphasize the tonal range of the guitar, Jimi would push down on the Wah pedal (a customised VOX wah) and play stinging high notes and then pull back on the Wah pedal and depress the vibrato to create a freight train like rumble. When fully depressing the bar to create these low notes the slack strings would often fall off the nut and have to be quickly snapped back in position.

Jimi's studio works "Third Stone from the Sun", "Axis: Bold as Love" and "Voodoo Child" (among others) introduced the world to this new use of the Stratocaster vibrato. Live tracks such as "The Star Spangled Banner" "I Don't Live Today" and "Machine Gun" featured the vibrato being used to mimic rockets, bombs and other sound effects, all within the context of blues-based psychedelic rock. To some degree, Hendrix used stage theatrics less and less as his career progressed, but feedback and vibrato remained a tremendous emotional outlet within his music.

Many rock bands of all types have used the tremolo for all sorts of effects, especially as a vibrato over chords. One guitarist especially known for his use of the bar is David Gilmour of the rock band Pink Floyd. This can be heard on countless songs. The last chord of the Rush song '2112' (Grand Finale) is a common reference. David Jon Gilmour CBE (born March 6, 1946 in Cambridge) is an English musician best known as a guitarist, singer, and songwriter in the band Pink Floyd. ... Pink Floyd are an English rock band that initially earned recognition for their psychedelic rock music, and, as they evolved, for their progressive rock music. ... Rush is a Canadian rock band comprising bassist, keyboardist, and lead vocalist Geddy Lee, guitarist Alex Lifeson, and drummer and lyricist Neil Peart. ...

Another, more extreme use of the tremolo bar, is the effect created by grabbing and shaking the bar violently. This style of playing is often used in the lead guitar breaks of death and thrash metal bands such as Slayer, Destruktur and Cannibal Corpse. This is often combined with natural and artificial harmonics, to make a 'screaming' or 'squealing' sound. The Floyd rose or Kahler systems are synonymous with this playing style, and Mattias IA Eklundh (Freak Kitchen and solo) is a modern master of these harmonic squeals.

On live versions of the song "In The Evening" by the band Led Zeppelin, guitarist Jimmy Page used a Fender Strat with a trem to create an effect where he made the pitch change with every chord, producing a wah wah sort of sound. For the bands 1969 self-titled debut album, see Led Zeppelin (album). ... James Patrick Jimmy Page, OBE (born 9 January 1944) is an English guitarist, composer and record producer. ...

Another example of the use of the tremolo bar is the song "Seven Seas" by TNT. In the guitar riff for this song, Ronni Le Tekro presses the tremolo bar against his guitar, creating a more fluid screeching sound. However, doing this can damage your guitar. Ronni Lé Tekrø (born 1963 in Norway) is a virtuoso guitarist best known for playing with the metal band TNT. His guitar riff [edit] The Le Tekro sound Ronni tends to play his guitar at a very fast pace, with more emphasis on distortion, and pace then loudness. ...

Former Pantera guitarist Dimebag Darrell is often said to have been one of the most influential users of the tremolo bar. His use of the tremolo bar contributed to the signature sounds and high pitched squeals that defined his playing. These techniques have influenced musicians of all ages and have advanced music in general. He extensively used the bar in all of his studio albums including Cowboys From Hell, Vulgar Display of Power, and New Found Power. For other uses, see Pantera (disambiguation). ... “Dimebag” redirects here. ... Cowboys from Hell is Panteras fifth album and their first Atco Records album, released on July 24, 1990 (see 1990 in music). ... Vulgar Display of Power is a groove metal album by heavy metal band Pantera, released on February 25, 1992 (see 1992 in music). ... New Found Power is the debut album by the band Damageplan. ...

Kevin Shields, the guitarist with groundbreaking alt rock/shoegaze band My Bloody Valentine created a new style of guitar playing known as 'glide guitar'. This is primarily characterised by extensive use of note bending, achieved via continuous manipulation of the tremolo arm on his Fender Jazzmaster. The best example of Shields' highly original guitar playing is the band's acclaimed final album Loveless. Kevin Shields (born Queens, New York City, USA on May 21, 1963) is a singer, guitarist, and producer who fronted the London-based band My Bloody Valentine in the late 1980s and early 1990s. ... The term alternative rock or alternative music1 was coined in the early 1980s to describe bands which didnt fit into the mainstream genres of the time. ... Shoegazing is a style of music that emerged in Britain in the late 1980s. ... This article is about the music group. ... Portamento is a musical term currently used to mean pitch bending or sliding, and in 16th century polyphonic writing refers to a type of musical ornamentation. ... This article does not cite its references or sources. ... Loveless is the second studio album by the Irish alternative rock band My Bloody Valentine. ...

Rage Against the Machine/Audioslave Guitarist Tom Morello has been known to use an Ibanez Locking Trem to create his sound on many of his solos. On the track "Sleep Now in the Fire" from The Battle of Los Angeles, he uses the tremolo bar in unison with kill-switching to raise and lower the sound of the feedback from his Amplifier to create a very rhythmic solo. On the Audioslave track Original Fire from Revelations, he depresses the bar to slack and then taps the strings against the pickups and then releases the bar to raise the pitch of the sound. This emulates the sound of monkeys laughing (solo at 2:28). Tom Morello (born May 30, 1964, as Thomas Baptist Morello) is a Grammy Award-winning American guitarist of the band Rage Against the Machine. ...

Adrian Belew has incorporated frequent use of the tremolo arm on his Stratocaster guitars as part of his unique and easily identifiable style. The tremolo arm is often integral to his use of the guitar to produce "sound effects" such as animal voices. On the track "Twang Bar King", from the album of the same title, he deliberately overuses the "twang bar" to create a camp parody of the technique. Adrian Belew in concert, November 2006. ... A Fender Stratocaster with rosewood fingerboard and three-tone sunburst finish. ... Camp is an aesthetic in which something has appeal because of its bad taste or ironic value. ...

Neil Young makes extensive use of a Bigsby vibrato in most of his electric-guitar work, producing an almost constant shifting of pitch in some solos, and simple chord-vibrato in rhythm work. This effect is accomplished by keeping a grip on the arm of the unit while moving the pick. This technique is prominent on more his more hard-rock songs such as "Like a Hurricane", "Hey Hey My My (Into the Black)" and "Rockin' in the Free World". This article is about the musician. ... The Bigsby vibrato tailpiece (or Bigsby for short) is a type of vibrato device for electric guitar designed by its namesake Paul A. Bigsby. ...

Joe Satriani uses the trem arm on his Ibanez Edge Trem System extremely often; most of the time to make his signature "Satch Scream", where he plays a harmonic near the bridge on the G-string and raises the bar. It can be heard on many of songs, including "Surfing With The Alien", "The Extremist", and "Flying In A Blue Dream". Joseph Satch Satriani (born on July 15, 1956, in Westbury, New York, U.S.) is an American guitarist and former guitar instructor. ...

Jeff Beck is an acknowledged master of the whammy bar. Arguably the best known example of his work, and something of a signature tune, is the track Where Were You from the 1989 album Jeff Beck's Guitar Shop. Geoffrey Arnold (Jeff) Beck (born June 24, 1944 to Arnold and Ethel Beck in Wallington, Greater London) is an English rock guitarist. ... Year 1989 (MCMLXXXIX) was a common year starting on Sunday (link displays 1989 Gregorian calendar). ... Jeff Becks Guitar Shop is a 1989 album by Guitar virtuoso Jeff Beck. ...

Sound files

Guitar vibrato Image File history File links Guitare_vibrato. ...

Brief sample of vibrato.

Problems listening to the file? See media help.

Riff with vibrato Image File history File links Vibrato-bar-riff. ...

Example of effects with the tremolo arm on some chords.

Problems listening to the file? See media help.

References

External links

General

• 1967 Fender Service Manual giving instructions for adjusting the then current Jaguar/Jazzmaster (floating), Stratocaster (synchronized), and Mustang (dynamic vibrato) tremolos, with diagrams of each.

Bigsby 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ...

• 1952 Bigsby twin neck, with Bigsby vibrato tailpiece clearly visible.

Synchronized tremolo

• Bridge routing patterns including several strat trem options, and showing the associated pivot screws, at Warmoth Guitars.

Floating tremolo Warmoth Guitar Products is an American manufacturer and distributor of electric guitar parts, catering particularly to small scale manufacturers, custom builders and amateur constructors. ...

• Buildup of a 1963 Fender Jaguar showing the installation of the tremolo unit.
• Exploded view of a Fender Jazzmaster showing the tremolo unit components.

Dynamic Vibrato 1962 Fender Jazzmaster Sunburst The Fender Jazzmaster electric guitar was introduced in 1958 and was designed as a more upmarket instrument than the Fender Stratocaster, which itself was introduced in 1954 as a higher-priced product than the companys Telecaster series. ...

• Mustang trem installation giving a routing template.

Vibrola and other Gibson trems

• Gibson Vibrola Tailpiece setup instructions for a side vibrato unit, with a diagram showing its operation.
• Jimi Hendrix's 1967 Gibson Flying V.

Locking tremolo

• Floyd Rose website.
• History of the Floyd Rose locking trem at the Kramer website.

Kahler tremolo This article or section does not cite any references or sources. ...

• Kahler Official Website

Stetsbar

• Website

Linear Tremolo

• Inventor's home page